05-15-2018
i would only copy the data files, assuming that the application programs are the at the same release. is there a separate /u file system?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
relup(5) Files relup(5)
NAME
relup - Release upgrade file
DESCRIPTION
The release upgrade file describes how a release is upgraded in a running system.
This file is automatically generated by systools:make_relup/3,4 , using a release resource file ( .rel ), application resource files ( .app
) and application upgrade files ( .appup ) as input.
FILE SYNTAX
In a target system, the release upgrade file should be located in the OTP_ROOT/erts-EVsn/Vsn directory.
The relup file contains one single Erlang term, which defines the instructions used to upgrade the release. The file has the following syn-
tax:
{Vsn,
[{UpFromVsn, Descr, Instructions}, ...],
[{DownToVsn, Descr, Instructions}, ...]}.
* Vsn = string() is the current version of the release.
* UpFromVsn = string() is an earlier version of the release to upgrade from.
* Descr = term() is a user defined parameter passed from the systools:make_relup/3,4 function. It will be used in the return value of
release_handler:install_release/1,2 .
* Instructions is a list of low-level release upgrade instructions, see appup(5) .
It consists of the release upgrade instructions from the respective application upgrade files (high-level instructions are translated
to low-level instructions), in the same order as in the start script.
* DownToVsn = string() is an earlier version of the release to downgrade to.
When upgrading from UpFromVsn with release_handler:install_release/1,2 , there does not have to be an exact match of versions, but
UpFromVsn can be a sub-string of the current release version.
SEE ALSO
app(5), appup(5), rel(5), release_handler(3erl), systools(3erl)
Ericsson AB sasl 2.1.9.3 relup(5)