05-15-2018
It is the enterprise version. Should I copy the entire disk or is there files that should not be copied? Thanks for the input.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
LEARN ABOUT HPUX
vxsplitlines
vxsplitlines(1M) vxsplitlines(1M)
NAME
vxsplitlines - show disks with conflicting configuration copies in a cluster
SYNOPSIS
vxsplitlines [-g diskgroup] [-c daname]
DESCRIPTION
If you import portions of a disk group on different systems, this can lead to conflicting configuration copies on the disks of the disk
group.
If the configuration information in a disk group is ambiguous, it may not be possible for Veritas Volume Manager to determine which config-
uration copy is most up-to-date. (This is usually termed a serial split brain (SSB) condition when it occurs in a cluster.) You cannot
import a disk group in this state unless you specify which disk's configuration copy to use.
You can use the vxsplitlines command to see which disks in a disk group have conflicting configuration copies, and use this information
together with your knowledge of the history of the disk groups' usage to determine which configuration copy is most valid.
The output from vxsplitlines displays the vxdg commands that you can run to import the disk group using the available configuration copies.
The -o selectcp option of the vxdg import command is used to select the configuration copy to use for the import.
OPTIONS
-c daname Display the SSB IDs for each disk that are stored in the configuration copy on the disk specified by its disk access name.
Note: Although the SSB IDs for some disks may match, this does not necessarily mean that those disks' configuration copies have
recorded all the configuration changes. When viewed from some other configuration copies, the SSB IDs of the same disks may not
match.
-g diskgroup
Specifies the disk group. If a disk group is not specified, the default disk group is used as determined from the rules on the
vxdg(1M) manual page.
EXAMPLES
Display the disks on each side of the split in the disk group newdg:
vxsplitlines -g newdg
Display the SSB IDs stored in the configuration copy on disk c2t4d0:
vxsplitlines -g newdg -c c2t4d0
NOTES
The vxsplitlines is primarily intended to be used with private disk groups, but it also works with shared disk groups.
The version number of the disk group must be 110 or greater.
SEE ALSO
vxdg(1M)
Veritas Volume Manager Administrator's Guide
VxVM 5.0.31.1 24 Mar 2008 vxsplitlines(1M)