05-15-2018
It is the enterprise version. Should I copy the entire disk or is there files that should not be copied? Thanks for the input.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
bcopy(9F) Kernel Functions for Drivers bcopy(9F)
NAME
bcopy - copy data between address locations in the kernel
SYNOPSIS
#include <sys/types.h>
#include <sys/sunddi.h>
void bcopy(const void *from, void *to, size_t bcount);
INTERFACE LEVEL
Architecture independent level 1 (DDI/DKI).
PARAMETERS
from Source address from which the copy is made.
to Destination address to which copy is made.
bcount The number of bytes moved.
DESCRIPTION
bcopy() copies bcount bytes from one kernel address to another. If the input and output addresses overlap, the command executes, but the
results may not be as expected.
Note that bcopy() should never be used to move data in or out of a user buffer, because it has no provision for handling page faults. The
user address space can be swapped out at any time, and bcopy() always assumes that there will be no paging faults. If bcopy() attempts to
access the user buffer when it is swapped out, the system will panic. It is safe to use bcopy() to move data within kernel space, since
kernel space is never swapped out.
CONTEXT
bcopy() can be called from user or interrupt context.
EXAMPLES
Example 1: Copying data between address locations in the kernel:
An I/O request is made for data stored in a RAM disk. If the I/O operation is a read request, the data is copied from the RAM disk to a
buffer (line 8). If it is a write request, the data is copied from a buffer to the RAM disk (line 15). bcopy() is used since both the RAM
disk and the buffer are part of the kernel address space.
1 #define RAMDNBLK 1000 /* blocks in the RAM disk */
2 #define RAMDBSIZ 512 /* bytes per block */
3 char ramdblks[RAMDNBLK][RAMDBSIZ]; /* blocks forming RAM
/* disk
...
4
5 if (bp->b_flags & B_READ) /* if read request, copy data */
6 /* from RAM disk data block */
7 /* to system buffer */
8 bcopy(&ramdblks[bp->b_blkno][0], bp->b_un.b_addr,
9 bp->b_bcount);
10
11 else /* else write request, */
12 /* copy data from a */
13 /* system buffer to RAM disk */
14 /* data block */
15 bcopy(bp->b_un.b_addr, &ramdblks[bp->b_blkno][0],
16 bp->b_bcount);
SEE ALSO
copyin(9F), copyout(9F)
Writing Device Drivers
WARNINGS
The from and to addresses must be within the kernel space. No range checking is done. If an address outside of the kernel space is
selected, the driver may corrupt the system in an unpredictable way.
SunOS 5.10 4 August 2003 bcopy(9F)