05-15-2018
It is the enterprise version. Should I copy the entire disk or is there files that should not be copied? Thanks for the input.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
cp(1) General Commands Manual cp(1)
Name
cp - copy file data
Syntax
cp [ -f ] [ -i ] [ -p ] file1 file2
cp [ -f ] [ -i ] [ -p ] [ -r ] file... directory
cp [ -f ] [ -i ] [ -p ] [ -r ] directory... directory
Description
The command copies file1 onto file2. The mode and owner of file2 are preserved if it already existed; the mode of file1 is used otherwise.
Note that the command will not copy a file onto itself.
In the second form, one or more files are copied into the directory with their original file names.
In the third form, one or more source directories are copied into the destination directory with their original file names.
Options
-f Forces existing destination pathnames to be removed before copying, without prompting for confirmation. The -i option is ignored if
the -f option is specified.
-i Prompts user with the name of file whenever the copy will cause an old file to be overwritten. A yes answer will cause to continue.
Any other answer will prevent it from overwriting the file.
-p Preserves (duplicates) in the copies the modification time, access time, file mode, user ID, and group ID as allowed by the permis-
sions of the source files, ignoring the present umask.
-r Copies directories. Entire directory trees, including their subtrees and the individual files they contain, are copied to the speci-
fied destination directory. The directory, its subtrees, and the individual files retain their original names. For example, to copy
the directory including all of its subtrees and files, into the directory enter the following command:
cp -r reports news
See Also
cat(1), pr(1), mv(1)
cp(1)