05-15-2018
do you have the enterprise or host version of sco? if you have tcp you should be able to use ftp to move tge data from one machine to the other. if both use the same sco license set the ip addresses to different class c networks and use a windows pc with an ip address on each network to talk to both.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
TALK(1) BSD General Commands Manual TALK(1)
NAME
talk -- talk to another user
SYNOPSIS
talk person [ttyname]
DESCRIPTION
The talk utility is a visual communication program which copies lines from your terminal to that of another user.
Options available:
person If you wish to talk to someone on your own machine, then person is just the person's login name. If you wish to talk to a user on
another host, then person is of the form 'user@host' or 'host!user' or 'host:user'.
ttyname If you wish to talk to a user who is logged in more than once, the ttyname argument may be used to indicate the appropriate terminal
name, where ttyname is of the form 'ttyXX'.
When first called, talk sends the message
Message from TalkDaemon@his_machine...
talk: connection requested by your_name@your_machine.
talk: respond with: talk your_name@your_machine
to the user you wish to talk to. At this point, the recipient of the message should reply by typing
talk your_name@your_machine
It does not matter from which machine the recipient replies, as long as his login-name is the same. Once communication is established, the
two parties may type simultaneously, with their output appearing in separate windows. Typing control-L '^L' will cause the screen to be
reprinted. Typing control-D '^D' will clear both parts of your screen to be cleared, while the control-D character will be sent to the
remote side (and just displayed by this talk client). Your erase, kill, and word kill characters will behave normally. To exit, just type
your interrupt character; talk then moves the cursor to the bottom of the screen and restores the terminal to its previous state.
Permission to talk may be denied or granted by use of the mesg(1) command. At the outset talking is allowed.
CONFIGURATION
The talk utility relies on the talkd system daemon. See talkd(8) for information about enabling talkd.
FILES
/etc/hosts to find the recipient's machine
/var/run/utmpx to find the recipient's tty
SEE ALSO
mail(1), mesg(1), wall(1), who(1), write(1), talkd(8)
HISTORY
The talk command appeared in 4.2BSD.
In FreeBSD 5.3, the default behaviour of talk was changed to treat local-to-local talk requests as originating and terminating at localhost.
Before this change, it was required that the hostname (as per gethostname(3)) resolved to a valid IPv4 address (via gethostbyname(3)), making
talk unsuitable for use in configurations where talkd(8) was bound to the loopback interface (normally for security reasons).
BUGS
The version of talk released with 4.3BSD uses a protocol that is incompatible with the protocol used in the version released with 4.2BSD.
Multibyte characters are not recognized.
BSD
August 21, 2008 BSD