Sponsored Content
Operating Systems SCO Installation on SCO Openserver 5.0.5 Post 303017383 by jgt on Tuesday 15th of May 2018 06:48:40 AM
Old 05-15-2018
Check the date in the CMOS. If it is prior to the date of the original install the system will not boot properly.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Help For SCO OpenServer

I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies

2. UNIX for Dummies Questions & Answers

sco openserver 5.5

hello! when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ? kindly help me thanks (1 Reply)
Discussion started by: buntty
1 Replies

3. IP Networking

Installation Problem in Unix Openserver

I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies

4. SCO

sco openserver 5.07 installation problem

Hi everyone, We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies

5. SCO

SCO OpenServer 5.0.7 Installation problem

we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached). At the time of installation we link both driver BTLD Boot: Defbootstr link=accraid ad320 Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies

6. SCO

openserver 6.0 installation PANIC

I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies

7. SCO

SCO OpenServer 5.0.7 Installation problem on HP ML310 G4

can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue tried hpsas aacraid lsil a160 a320 server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies

8. SCO

sco openserver release 5.0.5 installation problems on notebook

hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies

9. UNIX for Advanced & Expert Users

Installation of Sco Openserver 5.0.7 on HP DC 7600

Hi All , I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations. Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies

10. UNIX for Advanced & Expert Users

OpenServer 6.0v installation

Hi: I'm installing SCO Open Server 6.0v on VMWare ESXi, The instalation procedure giving by UnXis is using OVF deploy template and it create a primary partition of 10gb only. Any one know, if the OVF template could be edited to create a larger partition?? Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
DATETIME.SETDATE(3)							 1						       DATETIME.SETDATE(3)

DateTime::setDate - Sets the date

       Object oriented style

SYNOPSIS
public DateTime DateTime::setDate (int $year, int $month, int $day) DESCRIPTION
Procedural style DateTime date_date_set (DateTime $object, int $year, int $month, int $day) Resets the current date of the DateTime object to a different date. PARAMETERS
o $object -Procedural style only: A DateTime object returned by date_create(3). The function modifies this object. o $year - Year of the date. o $month - Month of the date. o $day - Day of the date. RETURN VALUES
Returns the DateTime object for method chaining or FALSE on failure. CHANGELOG
+--------+---------------------------------------------------+ |Version | | | | | | | Description | | | | +--------+---------------------------------------------------+ | 5.3.0 | | | | | | | Changed the return value on success from NULL to | | | DateTime. | | | | +--------+---------------------------------------------------+ EXAMPLES
Example #1 DateTime.setDate(3) example Object oriented style <?php $date = new DateTime(); $date->setDate(2001, 2, 3); echo $date->format('Y-m-d'); ?> Procedural style <?php $date = date_create(); date_date_set($date, 2001, 2, 3); echo date_format($date, 'Y-m-d'); ?> The above examples will output: 2001-02-03 Example #2 Values exceeding ranges are added to their parent values <?php $date = new DateTime(); $date->setDate(2001, 2, 28); echo $date->format('Y-m-d') . " "; $date->setDate(2001, 2, 29); echo $date->format('Y-m-d') . " "; $date->setDate(2001, 14, 3); echo $date->format('Y-m-d') . " "; ?> The above example will output: 2001-02-28 2001-03-01 2002-02-03 SEE ALSO
DateTime.setISODate(3), DateTime.setTime(3). PHP Documentation Group DATETIME.SETDATE(3)
All times are GMT -4. The time now is 10:45 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy