05-15-2018
Check the date in the CMOS. If it is prior to the date of the original install the system will not boot properly.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
DATE(1) General Commands Manual DATE(1)
NAME
date - print or set the date and time
SYNOPSIS
date [-qsu] [[MMDDYY]hhmm[ss]] [+format]
OPTIONS
-q Read the date from stdin
-s Set the time (implicit for -q or a date string)
-u Print the date as GMT
-t Use this number of seconds instead of current time
EXAMPLES
date # Print the date and time
date 0221921610 # Set date to Feb 21, 1992 at 4:10 p.m.
DESCRIPTION
With the -q flag or a numeric argument, date sets the GMT time and date. MMDDYY refers to the month, day, and year; hhmmss refers to the
hour, minute and second. Each of the six fields must be exactly two digits, no more and no less. date always display the date and time,
with the default format for the system. The -u flag request GMT time instead of local time. A format may be specified with a + followed
by a printf-like string with the following options:
%% % character
%A Name of the day
%B Name of the month
%D mm/dd/yy
%H Decimal hour on 2 digits
%I Decimal hour modulo 12 on 2 digits
%M Decimal minute on 2 digits
%S Decimal seconds on 2 digits
%T HH:MM:SS
%U Decimal week number, Sunday being first day of week
%W Decimal week number, Monday being first day of week
%X Same as %T
%Y Decimal year on 4 digits
%Z Time Zone (if any)
%a Abbreviated name of the day
%b Abbreviated name of the month
%c Appropriate date & time (default format)
%d Decimal day of the month on 2 digits
%e Same as %d, but a space replaces leading 0
%h Same as %b
%j Decimal dey of the year on 3 digits
%m Decimal month on 2 digits
%n Newline character
%p AM or PM
%r 12-hour clock time with AM/PM
%s Number of seconds since the epoch
%t Tab character
%w Decimal day of the week (0=Sunday)
%x Same as %D
%y Decimal year on 2 digits
SEE ALSO
time(2), ctime(3), readclock(8).
DATE(1)