05-15-2018
Firstly, let me try to understand what you have done.
Was the old server booting 5.0.5 before you started? Or are you restoring an old native backup onto it by booting from removable media (floppy, tape, whatever)? Obviously, if you are restoring a backup created on this old machine then it should work if you do it correctly (disaster recovery routine).
If you have restored a backup from the new machine onto the old machine then some drivers may be different which will prevent it running from a straight restore.
What format (cpio, tar, whatever) are the old machine's backups in?
What format are the new machine's backups in?
Please elaborate on the steps already taken.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
LEARN ABOUT DEBIAN
svn-fast-backup
svn-fast-backup(1) General Commands Manual svn-fast-backup(1)
NAME
svn-fast-backup - very fast backup for Subversion fsfs repositories.
SYNOPSIS
svn-fast-backup [-q] [-k{N|all}] [-f] [-t] [-s] repos_path backup_dir
DESCRIPTION
svn-fast-backup uses rsync snapshots for very fast backup of a Subversion fsfs repository at repos_path to backup_dir/repos-rev, the latest
revision number in the repository. Multiple fsfs backups share data via hardlinks, so old backups are almost free, since a newer revision
of a repository is almost a complete superset of an older revision.
This is good for replacing incremental log-dump+restore-style backups because it is just as space-conserving and even faster; there is no
inter-backup state (old backups are essentially caches); each backup directory is self-contained. It has the same command-line interface
as svn-hot-backup(1) (if you use --force), but only works for fsfs repositories.
svn-fast-backup keeps 64 backups by default and deletes backups older than these; this can be adjusted with the -k option.
OPTIONS
-h, --help
Shows some brief help text.
-q, --quiet
Quieter-than-usual operation.
-k, --keep=N
Keep a specified number of backups; the default is to keep 64.
-k, --keep=all
Do not delete any old backups at all.
-f, --force
Make a new backup even if one with the current revision exists.
-t, --trace
Show actions.
-s, --simulate
Don't perform actions.
AUTHOR
Voluntary contributions made by many individuals. Copyright (C) 2006 CollabNet.
2006-11-09 svn-fast-backup(1)