Sponsored Content
Operating Systems AIX DISK ARRAY PROTECTION SUSPENDED message following disk replacement Post 303016331 by hicksd8 on Tuesday 24th of April 2018 03:22:46 PM
Old 04-24-2018
I'm not an AIX/IBM expert but, talking generically, array degraded always means that there is no resilience because a disk needs replacing, or an array rebuild has failed for some reason e.g. the new disk does not have enough LBA's, has bad sectors, has also failed, or whatever.

Did the rebuild happen? Could you see substantial activity for a period? Or is that rebuild still running?????

Try re-seating the new drive again and initiate another rebuild.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Newbie: Sun Ultra 5 Disk Replacement

I have just started getting into unix and aquired a Sun Ultra 5 however the disk failed and I want to replace it with a spare maxtor 40Gb i have lying around. I need to partition and format the disk from its old windows format. I have looked up info on the format command in solaris 9 and I think i... (2 Replies)
Discussion started by: kalm
2 Replies

2. Solaris

Disk replacement with svm

I dont even know what raid level this is, but its raid 5 mirrored from the looks of it. I have a failed disk (t12) within this mirror. What is the best way to replace this disk? 2 things concern me, isn't there a command to prepare the disk for a hot swap? and what should i do with the... (3 Replies)
Discussion started by: BG_JrAdmin
3 Replies

3. Red Hat

Hard disk replacement

Hi all, I need some help with a RHEL 4 on a Sun Fire v65x machine. Some of the disks is damaged or has a hardware issue. This disk is connected to a hardware raid. The problem is that I don't know what is the brand, model and capacity of the disk. I've read the raid manual, but says... (3 Replies)
Discussion started by: adelgadom
3 Replies

4. Solaris

Disk Replacement SVM

Hello, Can someone advise the proper procedure for replacing a mirrored disk in SVM. I have checked the docs and various websites but the procedure seems to vary. This is what I would do... 1. Remove the db replicas from the bad disk. 2. Detach it from the mirror 3. Clear it with... (4 Replies)
Discussion started by: Actuator
4 Replies

5. HP-UX

need your help for HP virtual array 7400 disk replacement error

hi all! I found a the state of disk at JA0/D13 was failed this morning. then i replaced it this afternoon,but i run #dsp -s the array status displayed ==================================== STATUS Subsystem State: 1 The Subsystem is TESTING. The array is REBUILDING and is 87%... (0 Replies)
Discussion started by: JoyOnLine
0 Replies

6. AIX

errpt kept sending errors after disk replacement

Hi, The system is a Power6 8204 with an external storage 7031. OS is AIX 5.3. I replaced a failed disk hdisk28 and put it back to the volume group. Everything looks just fine. After the replacement, errpt has kept sending "Perm DISK OPERATION ERROR". Other than the error, everything still... (1 Reply)
Discussion started by: aixlover
1 Replies

7. Solaris

encapsulated root disk replacement

Hello, I have a Sparc system with encapsulated disks. Because of disk errors I had to replace rootdisk, I did it with vxdiskadm 4) replacement, vxdctl disable/enable, vxdiskadm 5) After it it the system boot failed, dropped back to the ok> prompt, message was: The file... (0 Replies)
Discussion started by: ggi
0 Replies

8. HP-UX

FAULTY DISK replacement HP rx4640

Hello, I'm new to this forum and as you will see from my question I'm new to UNIX as well. One of our costumers has HP rx4640 running on UNIX with two 300GB hot-swappable disks that are mirrored. They reported to us that one of the disks is faulty and they want us to take care of it. Below is... (16 Replies)
Discussion started by: gjk
16 Replies

9. AIX

Disk replacement on SharedVG.

Hi, One of my disk is in 'disk missing state'. It is a sharedVG and cluster nodes. The errpt keeps reporting stale partition error. lvs are in open/stale state. In this sceanario is replacing the disk the best practice? When i do a lsdev the disk is labelled as below. hdisk3 Available ... (2 Replies)
Discussion started by: ElizabethPJ
2 Replies

10. Filesystems, Disks and Memory

DISK ARRAY PROTECTION SUSPENDED message displayed following disk replacement

Hello, On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active. We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED. ... (1 Reply)
Discussion started by: terrya
1 Replies
GNOME-DISK-IMAGE-MOU(1) 					gnome-disk-utility					   GNOME-DISK-IMAGE-MOU(1)

NAME
gnome-disk-image-mounter - Attach and mount disk images SYNOPSIS
gnome-disk-image-mounter [--writable] [URI...] DESCRIPTION
gnome-disk-image-mounter can be used to set up disk images. Both regular files and GVfs URIs (such as smb://filer/media/file.iso) can be used in the URI parameter. If no URIs are given and a window server is running, a graphical file chooser will be presented. Note that gnome-disk-image-mounter will not mount filesystems or unlock encrypted volumes in the disk image - this responsibility is left to the automounter in GNOME Shell to ensure that the same interactions happen as if the disk image was a regular physical device or disc. By default the disk images are attached read-only, use the option --writable to change this. RETURN VALUE
gnome-disk-image-mounter returns 0 on success and non-zero on failure. AUTHOR
Written by David Zeuthen <zeuthen@gmail.com> with a lot of help from many others. BUGS
Please send bug reports to either the distribution bug tracker or the upstream bug tracker at https://bugzilla.gnome.org/enter_bug.cgi?product=gnome-disk-utility. SEE ALSO
gnome-shell(1), gnome-disks(1), udisks(8), losetup(8) GNOME
March 2013 GNOME-DISK-IMAGE-MOU(1)
All times are GMT -4. The time now is 05:18 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy