We are using hp's network node manager and would like to monitor quite a few of our aix boxes. It appears that nnm does not have AIX mibs by default. Does anyone know where i can find mibs for aix to load into nnm? Thanks (0 Replies)
Okay. I need help since I barely use M$ any more, the last time I used it for something other than school, work, or AIM was back in the days of WIN98. I was just reading the article on this site, Is Microsoft about to release a Windows “kill switch”? | Ed Bott's Microsoft Report | ZDNet.com, and... (0 Replies)
Hello all :)
I am new to scripting. I need somebody to help me write a script that can edit the files.
For eg: if i say ./script <ipadd> <hostname>
then it should change the ipaddress and hostname in the following files:
1. /etc/hosts
2. /etc/sysconfig/network
3.... (1 Reply)
hi,
i would like to share this
/etc/sysconfig/network-script/route-eth0
GATEWAY0=XXXXXX
NETMASK0=XXXXXX
ADDRESS0=XXXXXXX
a delete route command with "route del -net xxxx...." will work but if the above exist and you reboot the linux then old route will be invoke on that config-route.
... (0 Replies)
Hellow,
I have a smc2582w-b brigde/acces point whom i configured on my windows vista pc and it works i have wireless acces to my network.
Then i plugged it in to my 420r enterprise and it doesn't give any link activity on the lan piece of my server and my bridge/AP
when i plug the cable... (3 Replies)
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Dear Engineer,
Can anyone please inform me some application name like (CBQ) to control network bandwidth and please provide me the url to configure it.
With Best Regards,
Md. Abdullah-Al Kauser (0 Replies)
Dear Engineer,
Can anyone please inform me some application name like (CBQ) to control network bandwidth and please provide me the url to configure it.
With Best Regards,
Md. Abdullah-Al Kauser (1 Reply)
Discussion started by: makauser
1 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO vconfig(8)interfaces(5)vlan September 30 2007 VLAN-INTERFACES(5)