PMS(4)							   BSD Kernel Interfaces Manual 						    PMS(4)

NAME

     pms -- PS/2 auxiliary port mouse driver

SYNOPSIS

     pckbc* at isa?
     pms* at pckbc?
     wsmouse* at pms?

     options PMS_DISABLE_POWERHOOK
     options PMS_SYNAPTICS_TOUCHPAD
     options PMS_ELANTECH_TOUCHPAD

DESCRIPTION

     The pms driver provides an interface to PS/2 auxiliary port mice within the wscons(4) framework.  Parent device in terms of the autoconfigu-
     ration framework is pckbc(4), the PC keyboard controller.	``pms'' is a generic driver which supports mice using common variants of the PS/2
     protocol, including wheel mice of the ``IntelliMouse'' breed.  Wheel movements are mapped to a third (z-) axis.  The driver is believed to
     work with both 3-button and 5-button mice with scroll wheels.  Mice which use other protocol extensions are not currently supported, but
     might be if protocol documentation could be found.  Mouse related data are accessed by wsmouse(4) devices.

     The pms driver has been updated to attempt to renegotiate mouse protocol after seeing suspicious or defective mouse protocol packets, or
     unusual delays in the middle of a packet; this should improve the chances that a mouse will recover after being switched away or reset (for
     instance, by a console switch).

     The PMS_DISABLE_POWERHOOK kernel option disables PS/2 reset on resume.

     In addition, the pms driver supports the ``Synaptics'' and ``Elantech'' touchpads in native mode, enabled with the PMS_SYNAPTICS_TOUCHPAD and
     PMS_ELANTECH_TOUCHPAD kernel options.  This allows the driver to take advantage of extra features available on Synaptics and Elantech Touch-
     pads.  The following sysctl(8) variables control behavior of Synaptics touchpads:

     hw.synaptics.up_down_emulation
		   If the touchpad reports the existence of Up/Down buttons, this value determines if they should be reported as button 4 and 5
		   events or if they should be used to emulate some other event.  When set to 0, report Up/Down events as buttons 4 and 5.  When
		   set to 1, the Up and Down buttons are both mapped to the middle button.  When set to 2 (default), the Up and Down buttons are
		   used for Z-axis emulation, which more closely resembles how mouse wheels operate.

     hw.synaptics.up_down_motion_delta
		   When the Up/Down buttons are used for Z-axis emulation, this value specifies the emulated delta-Z value per click.

     hw.synaptics.gesture_move
		   Gestures will not be recognised if the finger moves by more than this amount between taps.

     hw.synaptics.gesture_length
		   Gestures will not be recognised if the number of packets (at 80 packets per second) between taps exceeds this value.

     hw.synaptics.edge_left

     hw.synaptics.edge_right

     hw.synaptics.edge_top

     hw.synaptics.edge_bottom
		   These values define a border around the touchpad which will be used for edge motion emulation during a drag gesture.  If a drag
		   gesture is in progress and the finger moves into this border, the driver will behave as if the finger continues to move in the
		   same direction beyond the edge of the touchpad.

     hw.synaptics.edge_motion_delta
		   This specifies the pointer speed when edge motion is in effect.

     hw.synaptics.finger_high
		   The driver will ignore new finger events until the reported pressure exceeds this value.

     hw.synaptics.finger_low
		   The driver will assume a finger remains on the touchpad until the reported pressure drops below this value.

     hw.synaptics.two_fingers_emulation
		   More recent touchpads can report the presence of more than one finger on the pad.  This value determines how such events are
		   used.  If set to 0 (default), two-finger events are ignored.  If set to 1, two-finger events generate a right button click.	If
		   set to 2, two-finger events generate a middle button click.

     hw.synaptics.scale_x

     hw.synaptics.scale_y
		   Scale factor used to divide movement deltas derived from Synaptics coordinates (0-6143) to yield more reasonable values
		   (default 16).

     hw.synaptics.max_speed_x

     hw.synaptics.max_speed_y
		   Limits pointer rate of change (after scaling) per reported movement event (default 32).

     hw.synaptics.movement_threshold
		   Movements of less than this value (in Synaptics coordinates) are ignored (default 4).

     The following sysctl(8) variables control behavior of Elantech touchpads:

     hw.elantech.xy_precision_shift

     hw.elantech.z_precision_shift
		   Increased values improve the accuracy of X, Y, and Z-axis reporting at the expense of slower mouse movement (default 2 for xy,
		   and 3 for z).

     For Elantech touchpads, the Z-axis is emulated using two-finger Y-axis reporting.

SEE ALSO

     pckbc(4), ums(4), wsmouse(4)

AUTHORS

     The pms driver was originally written by Christopher G. Demetriou.  The changes to merge the ``IntelliMouse'' protocol in, and reset the
     mouse in the event of protocol problems, were contributed by Peter Seebach.  Special thanks to Ray Trent, at Synaptics, who contributed valu-
     able insight into how to identify bogus mouse data.  The changes to add ``Synaptics'' pad support were by Ales Krenek, Kentaro A. Kurahone,
     and Steve C. Woodford.  The changes to add ``Elantech'' pad support were by Jared D. McNeill.

BUGS

     It is possible for the driver to mistakenly negotiate the non-scroll-wheel protocol, after which it is unlikely to recover until the device
     is closed and reopened.

     The ``Elantech'' pad code only supports trackpads with firmware version 2.48 or above.

BSD
								 December 13, 2008							       BSD