a) ICMP is stateless. So defining the state is senseless
b) ICMP Subtype 8 is echo Request, which you correctly defined on the INPUT Chain. ICMP Subtype 0 is "echo Reply" which is regulated at the OUTPUT chain since it is sent from the local host to the pinging party
c) Defining source -s 0/0 is of no use. Omit that and you have no restriction of source addresses.
d) I would assume the module icmp is automatically loaded when you specifiy -p icmp, so you can omit this too.
You can trace your paket filter more closely with additional log-rules before and after important Rules in your filter-definition.
Oh. Wait. I misunterstood. iptables is the pinging party....
Hi,
I want to enable hibernate in my machine.
when i click hibernate option, it is throwing message that hibernate is not enabled in kernel.
earlier, i was hibernating in the same machine with windows os.
any idea ?
Thx in advance.
Siva (0 Replies)
Hello everyone,
I installed AIX the other day (several times!) but I can't get XDMCP to work.
I remember from when I installed it the last time it worked out of the box.
So why doesn't it work now?
This is the error message I get:
XDMCP fatal error: Session failed Session 2 failed for... (3 Replies)
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Hi Folks!
I am writing a script which changes lpfc.conf if there it has been setup on RHEL BOXes, do I need to put dracut -f for enabling it? I am not sure,
Can someone help! (6 Replies)
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
I have installed the "mipsel tuxbox" compile suite for crosscompile
Host system is x86_64 slackware
destination is mipsel32bit "vuduo+"
For example,I want to compile a program, I use this script
make clean
export TOOLCHAIN=/opt/mipsel-tuxbox-linux-gnu
export... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies
LEARN ABOUT DEBIAN
tracestats
TRACESTATS(1) User Commands TRACESTATS(1)NAME
tracestats - perform simple analysis on a trace
SYNOPSIS
tracestats [ -f | --filter bpf ]... inputuri...
DESCRPTION
tracestats reads one or more traces and outputs summaries for each trace of how many packets/bytes match each bpf filter, as well as
totals. If instead of doing this for the entire trace, but to do it for portions then use tracertstats(1) instead.
-f bpf-filter
--filter bpf-filter
Add another bpf filter
EXAMPLES
tracestats --filter 'host sundown'
--filter 'port http'
--filter 'port ftp or ftp-data'
--filter 'port smtp'
--filter 'tcp[tcpflags] & tcp-syn!=0'
--filter 'not ip'
--filter 'ether[0] & 1 == 1'
--filter 'icmp[icmptype] == icmp-unreach'
erf:/traces/trace1.gz
erf:/traces/trace2.gz
LINKS
More details about tracestats (and libtrace) can be found at http://www.wand.net.nz/trac/libtrace/wiki/UserDocumentation
SEE ALSO libtrace(3), tracemerge(1), tracefilter(1), traceconvert(1), tracesplit(1), tracesplit_dir(1), tracereport(1), tracertstats(1), tracepkt-
dump(1), traceanon(1), tracesummary(1), tracereplay(1), tracediff(1), traceends(1), tracetopends(1)AUTHORS
Perry Lorier <perry@cs.waikato.ac.nz>
tracestats (libtrace) October 2005 TRACESTATS(1)