Sponsored Content
Full Discussion: Error F painit on bootup
Operating Systems SCO Error F painit on bootup Post 303015372 by jgt on Tuesday 3rd of April 2018 04:10:03 PM
Old 04-03-2018
I would suggest that you do one more thing since it appears that you will not be able to boot the system if the Axxon card fails.

Remove the driver, re-link the kernel and save it in /stand as unix.no_axxon, then re-install the driver.
If the card fails, or has to be removed, you can still get the system started by entering unix.no_axxon at the Boot: prompt.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Triple bootup

Hi guys, May I know how to install Solaris 8 in the way that I can triple boot it with my the other two OS: WIndows ME and Windows 2000 Pro. Can you all please kindly advise me on how to setup the triple boot process inorder to allow Windows ME to be the default OS when being ask to choose... (1 Reply)
Discussion started by: cia
1 Replies

2. Linux

Preventing a scan of the RAID during bootup

I have a RH 7.3 server that needs a restart today after putting a patch in place. The last time I rebooted this box was almost a year ago and when the uptime is quite long, Linux likes to check all the disks for errors, including the RAID. This adds almost 1.5Hrs to my bootup process:eek: . Does... (1 Reply)
Discussion started by: turbo90awd
1 Replies

3. UNIX for Advanced & Expert Users

bootup script

Hello there I need to run a script whenever i reboot or startup my HP-UX server. This script adds some routes to the route table, and it start third party aplications like "Star Manager". I thought i could do this simply putting the script in "/sbin/init.d, and a link to the script in... (7 Replies)
Discussion started by: vascobrito
7 Replies

4. UNIX for Dummies Questions & Answers

Bootup Error

Hi all The following error was displayed when a sco server (5.0.5) was booted. What should be done to overcome the problem. Replies appreciated. Bios 03.0 0130688 KB memory good 01 processor(s) in system remote console dialing on, please wait connect fail : modem off cpu clock... (6 Replies)
Discussion started by: raguramtgr
6 Replies

5. UNIX for Dummies Questions & Answers

Why not automatic bootup

Evry time I start up my mavhine ,have to type in unix at Boot : Is there a way unix should bootup automatically? Asif (2 Replies)
Discussion started by: asif iqbal
2 Replies

6. AIX

How to start ssh at bootup

Hi i installed ssh of version v 1.21 and my AIX is of 5.3. I want to start my ssh deamon at the startup can any one please help me out reg.. Thanks in advance.. (1 Reply)
Discussion started by: kmalla
1 Replies

7. AIX

File system not mounting at bootup

Hi, I've got a recent problem with 2 file systems on an AIX 5.3 server. The fs's are marked to auto mount at startup and do show as being mounted after a a restart however if you cd to the mount point and 'df -g .' it shows the fs hasn't actually mounted. $ mount |grep SQLT0001.0 ... (2 Replies)
Discussion started by: m223464
2 Replies

8. UNIX for Advanced & Expert Users

system slows after bootup for some time

Hi, I am using a Linux system running at run level 3. I am finding a wired problem, once the system boots, the system terminal slows down, I need to type the characters repeatedly to enter my login and password info. Also running any commands takes time, it stays in this condition for some... (1 Reply)
Discussion started by: cjjoy
1 Replies

9. UNIX for Dummies Questions & Answers

bootup sequence

What is the boot up sequence in UNIX? (2 Replies)
Discussion started by: karthi_g
2 Replies

10. Solaris

Sunfire X4600 Errors on Bootup

Hi Folks, Has anyone seen these errors on bootup. Mar 15 12:22:30 svc.startd: svc:/system/device/local:default: Method "/lib/svc/method/devices-local" failed due to signal SEGV.ht (c) 1983, 2010, Oracle and/or its affiliates. All rights reserved. Configuring devices. ... (1 Reply)
Discussion started by: ESSTEAM
1 Replies
DAIC(4) 						   BSD Kernel Interfaces Manual 						   DAIC(4)

NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10 DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO. For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd system, which can be listed using the daicctl utility. The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto- col and some parts of the cards interface are ISDN protocol dependent. The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992. MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd. Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu- mentation for details. The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte- grated. But if you own a card, you do have the file (or can get it from the Diehl web server). SEE ALSO
daicctl(1) BUGS
The driver is not yet finished. BSD
January 30, 1998 BSD
All times are GMT -4. The time now is 01:24 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy