03-09-2018
Hi,
I think I would start with some basics here assuming that the IP's are different, you could try;
- Ping the IP Addresses from your work station, check that they are around the same.
- Ping the URL for each and look for obvious differences to the IP Address pings.
- Run a traceroute from each and look for differences.
- Check and make sure that the reverse lookup is the same.
You could also look at things like the network config, between the switches if they are physically different.
It would also be worth looking at the /etc/network/interfaces file on the proxy.
There are just so many possibilities here, it will have to be a process of elimination.
Regards
Gull04
Last edited by gull04; 03-09-2018 at 09:19 AM..
Reason: Correction
This User Gave Thanks to gull04 For This Post:
9 More Discussions You Might Find Interesting
1. Linux
I have configured reverse proxy through apache...conf file is attached
My reverse proxy has a public ip.it is redirecting the request to 172.16.1.43 which is http
server.....Now i have a link in Http server's home page which will redirect the request to
another Lan zone machine... (0 Replies)
Discussion started by: dipanrc
0 Replies
2. UNIX for Dummies Questions & Answers
Hi
I am trying to set up two hosts in a reverse proxy. The reverse proxy already has 8 servers running perfectly, but they are all simply mapping pure addresses, which I have registered internally and externally.
The latest two I wish to add are a bit different, they are app servers, one... (1 Reply)
Discussion started by: rboekdrukker
1 Replies
3. IP Networking
Hi,
I am involved in a project on Debian. One of my requirement is to route an IP packet in my application to a proxy server and receive the reply from the proxy server as an IP packet. My application handles data at the IP frame level. My application creates an IP packet(with all the necessary... (0 Replies)
Discussion started by: Rajesh_BK
0 Replies
4. UNIX for Advanced & Expert Users
I'd just like to know what you use for user account management on your DMZ servers?
Do you use the same authentication realm as internally?
Do you use a different authentication realm, perhaps only for the DMZ?
Do you use local accounts? (2 Replies)
Discussion started by: humbletech99
2 Replies
5. UNIX for Advanced & Expert Users
Hi All,
I have a webpage loaded on server1 with authorization enabled by .htaccess, which can be accessed by http://ipofserver1/index.html. Now im planning a high availabilty load balancing in such a way that if the server1 is down due to some reason it should connect to another server. i have... (1 Reply)
Discussion started by: Tuxidow
1 Replies
6. UNIX for Advanced & Expert Users
Hi all,
The scenario is:
http://img834.imageshack.us/img834/7990/1234z.jpg
- With:
+ 192.168.100.0/24 : internet link (simulation)
+ Multiple Websites are hosting in local.
+ Complete DNS configuration.
+ OS: CentOS 5
- Requirements:
Configure Squid Proxy as... (0 Replies)
Discussion started by: kidzer0
0 Replies
7. Web Development
Reading Apache documentation I come to understand that it can host different websites, either by FQDN or IP address, virtually.
Is it possible for an Apache server to run two sites, and no one be able to tell from outside, that they are hosted in the same server? If not possible.
Essentially,... (2 Replies)
Discussion started by: Aia
2 Replies
8. Red Hat
Hi All
I need your valuable help on this. Im trying to setup reverse proxy using apache in rhel 5.5. I just started with Apache, and not much idea about going with advance level config, except that i have tried to set up this reverse proxy based on an online guide i found in internet. The... (0 Replies)
Discussion started by: niyas_gk
0 Replies
9. IP Networking
Hi, one member of WJ forum adviced that i setup an reverse proxy for my webserver. So im curious if anyone know about good, easy noob tutorial on hwo to achieve this, please link to this tutorial how to setup reverse proxy for an webserver.
Or better for whole node server with OpenVZ... (1 Reply)
Discussion started by: postcd
1 Replies
LEARN ABOUT DEBIAN
fstobdf
FSTOBDF(1) General Commands Manual FSTOBDF(1)
NAME
fstobdf - generate BDF font from X font server
SYNOPSIS
fstobdf [ -server servername ] -fn fontname
DESCRIPTION
The fstobdf program reads a font from a font server and prints a BDF file on the standard output that may be used to recreate the font.
This is useful in testing servers, debugging font metrics, and reproducing lost BDF files.
OPTIONS
-server servername
This option specifies the server from which the font should be read. servername must be specified in one of the formats defined in
the Font Server Names section of X(7). If not specified, the server name in the FONTSERVER environment variable is used.
-fn fontname
This option specifies the font for which a BDF file should be generated.
ENVIRONMENT
FONTSERVER
The default server to use. The server name must be specified in one of the formats defined in the Font Server Names section of
X(7).
SEE ALSO
xfs(1), bdftopcf(1), showfont(1), fslsfonts(1), X(7).
AUTHOR
Olaf Brandt, Network Computing Devices
Dave Lemke, Network Computing Devices
Jim Fulton, MIT X Consortium
X Version 11 fstobdf 1.0.5 FSTOBDF(1)