hello every one this is my first post ... well i'm new to linux ....
i've been enjoying shell scripting tutorials and i'm new to writting scripts
i want to write a script that creates a directory tree named in hexadecimal but i'm stuck at the hexadecimal part ... here is my code (incase i... (2 Replies)
Hi all,
I have a small script to convert my HexaDecimal Input to Decimal as output.
#!/bin/ksh
hd=00208060
dec=`printf %d $hd`
echo $dec
Output of the above program:
printf: 00208060 not completely converted
16
But my expected output is "2130016".
How can i acheive this.
I... (2 Replies)
Let's suppose i have a hexadecimal array with 16 cells.for example
b3e2d5f636111780
i want to convert it to an array of ascii characters(in C) so that
i can reduce total size of the file i want to put it in.
But i am afraid i have not fully understand the difference between ascii
and hex(i... (3 Replies)
Hi there !
I have text files with some nonsense characters in it, so different text editors put different nonsense symbols, and, worse, the application that should be able to read these files doesn't.
With xxd, the nonsense characters show as "efbfbd", while they should be "c2a7" (the... (2 Replies)
Hi Guys,
Is it possible to convert the hexadecimal to Binary by unix command.....I could not figure out....
If I need to convert AF6D to binary...what could be the way to do?
Thanks in advance!!
---------- Post updated at 02:57 AM ---------- Previous update was at 02:42 AM ----------
I... (6 Replies)
How can I convert hexadecimal values to Binary from the second field to the end
Input:
WS-2 23 345 235
DT-3 45 4A3 000
pp-2 76 300 E4
Output:
WS-2 100011 1101000101 1000110101
DT-3 1000101 10010100011 000
pp-2 1110110 1100000000 11100100 (16 Replies)
Dear all,
I am trying to write c-program to read the following file containing hexadecimal values (snippet of big data file).
I want to combine two hexadecimal values together like A0A03E01 and then would like to have the binary equivalent to perform further test on it. Unfortunately, it failed... (16 Replies)
IFSYSCTL(5) Network configuration IFSYSCTL(5)NAME
ifsysctl[-<interface name>] - per network interface sysctl settings
SYNOPSIS
/etc/sysconfig/network/ifsysctl
/etc/sysconfig/network/ifsysctl-<interface name>
DESCRIPTION
These files are intended to contain sysctl settings, that should be applied when a network interface is created. This are usually interface
specific settings, like:
net.ipv6.conf.eth0.use_tempaddr = 1
or
net.ipv4.conf.eth0.rp_filter = 0
The settings are applied by the /etc/sysconfig/network/scripts/ifup-sysctl script executed via /etc/udev/rules.d/77-network.rules rule (see
udev(7)), after the creation and after the rename of the interface name to its persistent name (when applicable), but before the ifup
<interface name> -o hotplug may be executed to configure the interface.
The settings are not applied by default when the NetworkManager is active (NETWORKMANAGER=yes), except when the IFSYSCTL_NETWORKMANAGER=yes
variable is set in the /etc/sysconfig/network/config file.
Settings from the ifsysctl- file are applied every time an interface has been created.
Settings from the ifsysctl-interface name file are applied when the interface with the corresponding interface name has been created.
SYNTAX
The sysctl(8) utility is required to apply the settings. It supports two separator characters for sysctl keywords: a "." in default format
and a "/" in the alternate format. Therefore the syntax is basically same to the /etc/sysctl.conf file.
Interface names may contain a ".". In the default sysctl format using a "." as separator, that is any "." in the interface name of the key-
word, has to be replaced with a "/". In the alternate sysctl format with "/" as separator, normal interface names can be used.
Optionally, the ifsysctl files may contain also the $INTERFACE and the $SYSCTL_IF variables, that are automatically replaced with the cur-
rent interface name usable in the alternate format and with the sysctl-quoted interface name for the default format, before the settings
are passed to the sysctl utility.
Note also, that settings with variables in the ifsysctl (without the -<interface name> suffix), will be applied for every interface!
Further, files with variables are not compatible to the /etc/sysctl.conf file.
EXAMPLES
Settings for "eth0" and "eth0.1" interfaces
# using "." as separator:
net.ipv6.conf.eth0.use_tempaddr = 1
net.ipv6.conf.eth0/1.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/eth0/use_tempaddr = 1
net/ipv6/conf/eth0.0/use_tempaddr = 1
Settings with variables:
# using "." as separator:
net.ipv6.conf.$SYSCTL_IF.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/$INTERFACE/use_tempaddr = 1
To test your ifsysctl-eth0 or ifsysctl file, use:
/etc/sysconfig/network/scripts/ifup-sysctl eth0 -o debug
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO ifup(8)ifcfg(5)sysctl(8)sysconfig December 2009 IFSYSCTL(5)