01-17-2018
This User Gave Thanks to achenle For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I couldnt get my hands on my solaris 2.6 cd soo i used solaris 7 cd to boot to single user mode. I typed
boot cdrom -s
it bought me to my root prompt , but when i typed fsck.....nothing happened. It was as though it couldnt go ahead with fscking. it just bought up the prompt again,... (1 Reply)
Discussion started by: lealyz
1 Replies
2. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
3. UNIX for Advanced & Expert Users
Our V480 w/ Solaris 9 would not boot properly. After recreating the LUNs on our StorEdge A1000, and then performing a reboot, the machine just keep cycling through the boot process. No error messages, it keeps trying to reboot over and over again.
Any ideas?
We managed to do a stop+a and... (6 Replies)
Discussion started by: xnightcrawl
6 Replies
4. Solaris
Dear all,
Every time I boot my Ultra 60, after initializing the memory I always have to type boot at the ok>
Rebooting with command boot
Boot device: disk0 File and args :
Trap 3e
(0) ok
I've tried to re-installed the machine but result is the same...
What would be the problem?
... (4 Replies)
Discussion started by: frankoko
4 Replies
5. Solaris
Hi
using solaris 5.8 on UltraSPARC-IIi 360MHz.
I know it is an old hardware but similiar hardware is running fine. here is the issue,
System booted : works okay for some time then display was hung so system was rebooted ..it gave data access error. again rebooted and it came up... (6 Replies)
Discussion started by: upengan78
6 Replies
6. Solaris
Hi All ,
I am unable to reinstall the OS on my Ultra Sparc 10. After the 1st CD is loaded when it goes for reboot its goes to ok prompt an its unable to boot.
What could be reason for this behavior? while loading the OS its seems fine but unable to boot!!
Then i tried changing the... (2 Replies)
Discussion started by: kumarmani
2 Replies
7. Solaris
Hi All
We have the Sun Solaris server ... Got a power cut suddenly .... Crash happened to the system almost
You can access through Termnl .. But it seems he did not boot ... How to Make the process of the boot correctly without losing information
Thanks for all (3 Replies)
Discussion started by: gogo888
3 Replies
8. Ubuntu
hello,
before i have install solaris 9, is good.
I would like to install Ubuntu 10.04 on a Sun Blade 150 blade.
I create cdrom iso burning with a 10x
was open I made a boot ok: boot cdrom
I get the following error:
fast data access mmu miss
i do
probe-ide all
reset-all
always
... (2 Replies)
Discussion started by: philo_71
2 Replies
9. Solaris
Hello everyone,
This is the first time I am installing Solaris. I have SunBlade 1500 Wrkstn. I installed Solaris 10 Sparc.
The installation went successfully but I don't get the login screen. I get the following error message:
Boot device: disk:a File and agrs:-
Data Access Error
Ok
... (4 Replies)
Discussion started by: mfsaeed
4 Replies
10. Solaris
Hi
I have a problem on a server, when he boot I have this type of message loop, do you know what it corresponds to ?
( requesting internet Adress for 0:3:ba:fa:33:91 )
Regards
Sun Fire V240, No Keyboard
Copyright 2007 Sun Microsystems, INC. All rights reserved.
openboot 4.22.33,... (10 Replies)
Discussion started by: yoyo-tns
10 Replies
LEARN ABOUT FREEBSD
boot.config
BOOT.CONFIG(5) BSD File Formats Manual BOOT.CONFIG(5)
NAME
boot.config -- Configuration file for the boot blocks
DESCRIPTION
The boot.config file contains options for the FreeBSD boot block code.
When the FreeBSD boot loader runs, it searches the ``a'' slice of the boot partition for a boot.config file (as a result, slices which are
missing an ``a'' partition require user intervention during the boot process). If the boot.config file is found, its contents are used as
the default configuration options for the boot block code and are echoed to the system console.
A valid format of this file is to put BIOS drive number, a controller type, a unit number, a partition, a kernel file name, and any other
valid boot(8) option on a single line, as it is done at the ``boot:'' prompt.
The options related to the boot image selection described below and all the other options available for boot.config are documented in detail
in the boot(8) manual page.
FILES
/boot.config parameters for the boot blocks (optional)
EXAMPLES
The command:
# echo "-P" > /boot.config
will activate the serial console of FreeBSD.
The command:
# echo "1:ad(1,a)/boot/loader" > /boot.config
will instruct the second stage of boot(8) on the first disk to boot with the third boot(8) stage from the second disk.
The command:
# echo "1:ad(1,a)/boot/loader -P" > /boot.config
will do both of the above.
SEE ALSO
boot(8), loader(8)
AUTHORS
This manual page was written by Daniel Gerzo <danger@FreeBSD.org>.
BSD
May 13, 2007 BSD