Sponsored Content
Operating Systems Solaris Solaris can not boot because metadb lost Post 303008674 by dzung on Monday 4th of December 2017 09:35:30 PM
Old 12-04-2017
Solaris can not boot because metadb lost

how to recovery metadb?
Thanks!
 

10 More Discussions You Might Find Interesting

1. Solaris

solaris boot problem boot error loading interpreter(misc/krtld)

When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error. cannot find mis/krtld boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies

2. Solaris

solaris with metadb

Hi All, If solaris has metadb services on the disk, it means that it has a HW raid controller. Or what. Thanks in advance. (1 Reply)
Discussion started by: itik
1 Replies

3. Solaris

metadb problem - server unable to boot

Hi everyone I have a problem. My configuration is as follows: Sun 280R server 2 x internal disks 3 x state databases on disk 1 3 x state databases on disk 2 Disk 1 was giving errors, so I cleared the mirrors on it, deleted the state databases and replaced the disk. Before attaching... (5 Replies)
Discussion started by: soliberus
5 Replies

4. Solaris

Solaris x86 installation using jumpstart does not local boot ( boot from hdd)

I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies

5. Solaris

How to create metadb with zpool in Solaris 11

Hi, my root pool is as follows. How can I create a metadb if I want to create SVM volumes? zpool status pool: rpool1 state: ONLINE scan: none requested config: NAME STATE READ WRITE CKSUM rpool1 ONLINE 0 0 0 c4t1d0s0 ... (10 Replies)
Discussion started by: incredible
10 Replies

6. What is on Your Mind?

Lost Sun Solaris 10Certification

.............. (1 Reply)
Discussion started by: siddulamadhu
1 Replies

7. Solaris

Boot disk crash with metadb config info

Hello all; We have a SunFire V240 with three disks that were part of a metadb. One of those disks, the boot disk, experienced a horrible death Monday night and we're now trying to recover from that. I know very little about metadb stuff, so please be gentle with me... I'm assuming... (3 Replies)
Discussion started by: Handon
3 Replies

8. Solaris

Check Solaris VM Databases metadb does not have enough information about logical volumes

Check Solaris VM Databases metadb does not have enough information about logical volumes. Current value is 0% I have checked the SVM status, all disks are good state and synched perfectly. no errors in metadb -i. what is this alert exact mean? what we have to check for the value? Please... (1 Reply)
Discussion started by: Naveen.6025
1 Replies

9. Solaris

Solaris 10 Volume Manager - adding slice to metadb

Hi all, I added a new disk slice to the current metadb. Below is what I see bash-3.2# metadb -i flags first blk block count a m p luo 16 8192 /dev/dsk/c0t0d0s7 a p luo 8208 8192 ... (3 Replies)
Discussion started by: javanoob
3 Replies

10. Solaris

Solaris stuck during boot after reconfigure boot

Hello, I have a problem with my machine that won't boot properly. The story is that I installed a software called apcupsd, which is a control application for my APC battery UPS. I have used version 3.14.10 earlier, but as part of restoring my previously crashed os harddrive I wanted to... (18 Replies)
Discussion started by: Zorken
18 Replies
ovdb_recover(8) 					    InterNetNews Documentation						   ovdb_recover(8)

NAME
ovdb_recover - Perform recovery on the ovdb database, if needed SYNOPSYS
ovdb_recover [-f] DESCRIPTION
Attempts to open the ovdb database, and if the database needs recovery, it attempts to perform the recovery. Similar in function to the BerkeleyDB db_recover command. Specify the `-f' option to force a recovery, even if the database appears to not need it. It is not an error to perform a recovery opera- tion on a clean database. However, do not run `ovdb_recover -f' while the database is in use by any other processes. Returns exit status of 0 if the database did not need recovery or if recovery succeeded, and returns exit status 1 if recovery failed. In the latter case, the database may be damaged beyond repair, requiring a rebuild with makehistory(8). This command is normally called automatically by rc.news(8). HISTORY
Written by Heath Kehoe <hakehoe@avalon.net> for InterNetNews. SEE ALSO
ovdb(5), makehistory(8) 3rd Berkeley Distribution INN 2.3 ovdb_recover(8)
All times are GMT -4. The time now is 09:57 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy