12-02-2017
Quote:
Originally Posted by
LoLo92
My Cluster state is STABLE but Resource Group on both nodes is UNMANAGED.
This means that the cluster will not do anything even if the node where your application runs would crash. "UNMANAGED" means the RG is not running as part of the cluster at all.
To correct this stop the application, unmount its filesystems and
varyoffvg its VGs. Then use either SMITty or the
clmgr command to start the resource group on one of your nodes. This will mount the FSes again and start the appication, so from a users POV nothing has changed. From the clusters POV, though, the RG is now under observation by the cluster services and if the node fails somehow (crashes, loses network connectivity, whatever else) the RG will be taken over to the other node.
I hope this helps.
bakunin
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
my partner change the server's ip address and now i can't to mount the oracle's filesystem, what i do? i don't want to reinstall Unix. My unix is SCO UNIX 5.0.5 (9 Replies)
Discussion started by: marun
9 Replies
2. Shell Programming and Scripting
Hi
How can I only print the file systems that are more than 95% full.
I used the df -k output and tried to check for each file system and then print only the ones that meet the criteria... But my solution seems cloodgie ... (3 Replies)
Discussion started by: YS2002
3 Replies
3. Filesystems, Disks and Memory
Dear Experts,
Is it possible to take a backup of two file systems using a single vdump command?
Thanks
Wilson (4 Replies)
Discussion started by: geraldwilson
4 Replies
4. UNIX for Advanced & Expert Users
Dear All
We have HP9000 rp7400 Server running with hp-ux 11i.
Our Disk storage has two volume groups and are allocated as follows:
1. /#vgdisplay -v
--- Volume groups ---
VG Name /dev/vg00
VG Write Access read/write
VG Status available... (1 Reply)
Discussion started by: mhbd
1 Replies
5. AIX
Hello all. Yes, I searched the forum first :)
I have hacmp running on 2 nodes. I wish to add a filesystem to the primary node to and existing shared VG. Not sure how to do this in a cluster environment.
My scenario:
Create the fs in the hacmp screens in smit add in the fs to and... (1 Reply)
Discussion started by: mhenryj
1 Replies
6. UNIX for Dummies Questions & Answers
how to check the record of previously mounted remote filesystems after the filesystems are unmounted .operating system is solaris 10 (0 Replies)
Discussion started by: ravijanjanam12
0 Replies
7. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
8. Shell Programming and Scripting
i need to write a shell script for printing the list of filesystems whose disk utilization is more than 75%...i tried using df -h along with awk but cud'nt make the combination work.....:wall:
when we do df -h then the filesystems which are using more than 75% capacity shud be printed according to... (11 Replies)
Discussion started by: xtatic
11 Replies
9. Shell Programming and Scripting
I need a scrip that will show me the filesystems that are greater than 70%...but not sure how to filter using the df -h | grep
Thank you for your help!! (6 Replies)
Discussion started by: eponcedeleonc
6 Replies
10. Solaris
SunOS 5.10 Generic_142900-15 sun4u sparc SUNW,SPARC-Enterprise
How can I tell if "clustering" is being used in my shop?
I have to file systems that are identical. These filesystems are nfs mounted. But how can I tell if they are being kept in sync as a result of clustering or some other... (2 Replies)
Discussion started by: Harleyrci
2 Replies
cmruncl(1m) cmruncl(1m)
NAME
cmruncl - run a high availability cluster
SYNOPSIS
cmruncl [-f] [-v] [-n node_name...] [-t | -w none]
DESCRIPTION
cmruncl causes all nodes in a configured cluster or all nodes specified to start their cluster daemons and form a new cluster.
To start a cluster, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the cluster configuration
file. See access policy in cmquerycl(1m).
This command should only be run when the cluster is not active on any of the configured nodes. This command verifies the network configu-
ration before causing the nodes to start their cluster daemons. If a cluster is already running on a subset of the nodes, the cmrunnode
command should be used to start the remaining nodes and force them to join the existing cluster.
If node_name is not specified, the cluster daemons will be started on all the nodes in the cluster. All nodes in the cluster must be
available for the cluster to start unless a subset of nodes is specified.
Options
cmruncl supports the following options:
-f Force cluster startup without warning message and continuation prompt that are printed with the -n option.
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages.
The -w option is not required with the -t option as -t does not validate network connectivity, but assumes that all the
nodes can meet any external dependencies such as EMS resources, package subnets, and storage.
-n node_name...
Start the cluster daemon on the specified subset of node(s).
-w none By default network probing is performed to check that the network connectivity is the same as when the cluster was config-
ured. Any anomalies are reported before the cluster daemons are started. The -w none option disables this probing. The
option should only be used if this network configuration is known to be correct from a recent check.
RETURN VALUE
cmruncl returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Run the cluster daemon:
cmruncl
Run the cluster daemons on node1 and node2:
cmruncl -n node1 -n node2
AUTHOR
cmruncl was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmhaltnode(1m), cmrunnode(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmruncl(1m)