Execution problems with sun blade 150 Post: 303005684

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Memory upgrade Sun Blade 150

I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system." Does anyone know if any SDRAM, PC133 � CL=2 � Unbuffered � ECC � 133MHz � 3.3V ...

2. UNIX for Dummies Questions & Answers

Please help to configure Sun Blade 150 workstation

Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help...

3. Solaris

Sun Blade 150 - I can't hook up extra drives

I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks...

4. Solaris

Sun Blade 100 cdrom problems...

FYI noob to here and sun blades... I have a sun blade 100 and I can't get the cdrom to work. if i try using vold that doesn't seem to work either...maybe i'm not using it correctly. Upon boot you can open/close the cdrom and it runs but after i'm logged in it won't open and i can't access it...

5. Solaris

Jumpstart Solaris 8 on Sun Blade 150 Hangs

We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there. We have 1 combined jumpstart server and it is also our NIS+...

6. Solaris

Solaris: Blade 150 - XWINDOWS Problem

Hi, I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console. But, if I insert the monitor cable to the XVR500 port,...

7. Solaris

Sun Blade 150 not a Sun?

I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05. I have just noticed /bin/sun now returns false, rather than true. See below. $ uname -a SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100 $ /bin/sparc &&...

8. Solaris

Sun Blade 150 wont boot off cdrom

Hello, Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall:

9. Solaris

Sun Blade 150 will not boot off harddrive after install of solaris 10

Hello, I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall:

10. Solaris

Cannot install or run Solaris 8 on Sun Blade 150

Hi everybody, I'm having big troubles in installing Solaris 8 on a Sun Blade 150. Here are some system specs: Sun Blade 150 (UltraSPARC-IIe 550MHz) RAM: 256MB OBP 4.10.6 2003/06/06 12:30 POST 2.0.1 2001/08/23 17:13 When I try to boot from Solaris 8 CD with boot cdrom or...

LEARN ABOUT LINUX

grub-install

GRUB-INSTALL(8) 					  System Administration Utilities					   GRUB-INSTALL(8)

NAME

       grub-install - install GRUB to a device

SYNOPSIS

       grub-install [OPTION] install_device

DESCRIPTION

       Install GRUB on your drive.

       -h, --help
	      print this message and exit

       -v, --version
	      print the version information and exit

       --modules=MODULES
	      pre-load specified modules MODULES

       --boot-directory=DIR
	      install GRUB images under the directory DIR/grub instead of the /boot/grub directory

       --grub-setup=FILE
	      use FILE as grub-setup

       --grub-mkimage=FILE
	      use FILE as grub-mkimage

       --grub-mkrelpath=FILE
	      use FILE as grub-mkrelpath

       --grub-mkdevicemap=FILE use FILE as grub-mkdevicemap

       --grub-probe=FILE
	      use FILE as grub-probe

       --no-floppy
	      do not probe any floppy drive

       --allow-floppy
	      Make the drive also bootable as floppy (default for fdX devices). May break on some BIOSes.

       --recheck
	      probe a device map even if it already exists

       --force
	      install even if problems are detected

       --disk-module=MODULE
	      disk module to use

       INSTALL_DEVICE can be a GRUB device name or a system device filename.

       grub-install copies GRUB images into /boot/grub, and uses grub-setup to install grub into the boot sector.

REPORTING BUGS

       Report bugs to <bug-grub@gnu.org>.

SEE ALSO

       grub-mkconfig(8), grub-mkimage(1), grub-setup(8), grub-mkrescue(1)

       The full documentation for grub-install is maintained as a Texinfo manual.  If the info and grub-install programs are properly installed at
       your site, the command

	      info grub-install

       should give you access to the complete manual.

grub-install (GRUB) 1.99-12ubuntu5				   October 2011 						   GRUB-INSTALL(8)