Execution problems with sun blade 150 Post: 303005680

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Memory upgrade Sun Blade 150

I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system." Does anyone know if any SDRAM, PC133 � CL=2 � Unbuffered � ECC � 133MHz � 3.3V ...

2. UNIX for Dummies Questions & Answers

Please help to configure Sun Blade 150 workstation

Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help...

3. Solaris

Sun Blade 150 - I can't hook up extra drives

I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks...

4. Solaris

Sun Blade 100 cdrom problems...

FYI noob to here and sun blades... I have a sun blade 100 and I can't get the cdrom to work. if i try using vold that doesn't seem to work either...maybe i'm not using it correctly. Upon boot you can open/close the cdrom and it runs but after i'm logged in it won't open and i can't access it...

5. Solaris

Jumpstart Solaris 8 on Sun Blade 150 Hangs

We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there. We have 1 combined jumpstart server and it is also our NIS+...

6. Solaris

Solaris: Blade 150 - XWINDOWS Problem

Hi, I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console. But, if I insert the monitor cable to the XVR500 port,...

7. Solaris

Sun Blade 150 not a Sun?

I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05. I have just noticed /bin/sun now returns false, rather than true. See below. $ uname -a SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100 $ /bin/sparc &&...

8. Solaris

Sun Blade 150 wont boot off cdrom

Hello, Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall:

9. Solaris

Sun Blade 150 will not boot off harddrive after install of solaris 10

Hello, I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall:

10. Solaris

Cannot install or run Solaris 8 on Sun Blade 150

Hi everybody, I'm having big troubles in installing Solaris 8 on a Sun Blade 150. Here are some system specs: Sun Blade 150 (UltraSPARC-IIe 550MHz) RAM: 256MB OBP 4.10.6 2003/06/06 12:30 POST 2.0.1 2001/08/23 17:13 When I try to boot from Solaris 8 CD with boot cdrom or...

LEARN ABOUT CENTOS

hpipower

hpipower(1)							      OpenHPI							       hpipower(1)

NAME

       hpipower - This sample openhpi application exercises HPI Power Management APIs.

SYNOPSIS

	hpipower [ -D nn ] [-N host[:port]] [-C <cfgfile>] [ -d -p -r -u -X -h] [ -b n ]
	hpipower [--domain=nn] [--host=host[:port]] [--cfgfile=file]
		 [--power-down --power-up --reset --unattended --debug --help] [--blade=n ]

DESCRIPTION

       hpipower searches the Resource Presence Table (RPT) for resources with Power Capability. It sends the requested power action to the
       selected target.

       If no domain or host is selected, hpipower uses the default domain as specified in the openhpiclient.conf file.

OPTIONS

   Help Options:
       -h, --help
	 Show help options

   Application Options:
       -d, --power-down
	 Power down target object

       -p, --power-up
	 Power on target object

       -r, --reset
	 Reset target object

       -u, --unattended
	 Unattended

       -b n, --blade=n
	 Specify blade n (1...n)

       -D nn, --domain=nn
	 Select domain id nn

       -X, --debug
	 Display debug messages

       -N "host[:port]", --host="host[:port]"
	 Open session to the domain served by the daemon at the specified URL (host:port).  This option overrides the OPENHPI_DAEMON_HOST and
	 OPENHPI_DAEMON_PORT environment variables.  If host contains ':' (for example IPv6 address) then enclose it in square brackets.  For
	 example: "[::1]" or "[::1]:4743".

       -C "file", --cfgfile="file"
	 Use passed file as client configuration file.	This option overrides the OPENHPICLIENT_CONf environment variable.

SEE ALSO

		hpi_shell
		hpialarms      hpifan	      hpireset	     hpitop
		hpidomain      hpigensimdata  hpisensor      hpitree
		hpiel	       hpiiinv	      hpisettime     hpiwdt
		hpievents      hpionIBMblade  hpithres	     hpixml
		ohdomainlist   ohhandler      ohparam

AUTHORS

       Authors of this man page:

	Peter D Phan (pdphan@users.sourceforge.net)
	Ulrich Kleber (ulikleber@users.sourceforge.net)
	Anton Pak (avpak@users.sourceforge.net)

3.2.1								    2011-09-20							       hpipower(1)