Hi,
I am using SCO OpenServer 5
During boot I get this message:
How can I fix this? I have no boot/root floppy.
If it is a "disk full" issue, is there a way to mount from Linux floppy/cd and delete some stuff?
Thank you very much
Could somone please tell me what happened when I reboot my computer, it take too long to pass the part it said "starting sendmail"
I only changed the server name and when I reboot the server, all of the services are running except when it got to :
starting sendmail
it take toooo long to... (1 Reply)
Hi All,
1st HDD is loaded with Windows 2000 Professional and I have installed Red Hat ES 3.0 on second HDD(80GB). After linux installation failed to load windows and boot stucks with displaying only L How to fix this issue
Thanks in advance for your valuable answer.
Regards,
Bachegowda (1 Reply)
Hi,all:
I want to boot an IA unix box from network, I am sure I set the DHCP and boot server, but it still failed !
It says : Client MAC Address: 00 18 FE 28 91 82 .....-
PXE-E16: Valid PXE offer not received.
Load of Core LAN Gb A failed: Not Found
I use the nettl command to trace the UDP... (0 Replies)
Hello, have HP Visualize C3600 workstation. Issue is as follows:
When I attempt to boot, unit will not boot successfully and will halt at a menu, the same menu as when during a boot one hits any key within 10 seconds to discontinue. When I attempt to boot with Boot primary, both with IPL... (17 Replies)
I had logged into Server via ALOM and was placed into runlevel 5 other than 3 which is default.
I did a svcadm delete boot-archive, and was promptly placed in runlevel 3.
Now, I am unable to do a telnet or login into the server through any other service.
bash-3.00# svcs -a
svcs -a
STATE ... (3 Replies)
Machine: x86
OS : Dualboot Solaris and RHEL5 -Solaris 10 in first fdisk partition.
RHEL5 - /boot in partition2
/ in partition3
swap in 1st... (1 Reply)
Hi,
I have a laptop with two os running in it, Windows XP & RHEL5. Accidentally, we have deleted the windows entry in grub.conf file. Later we connected the hard disk of laptop to another system & deleted the linux partitions from the disk management tool of windows.
Now the issue is, the... (7 Replies)
Hi all
i have an issue
when i change auto-boot?=false and reboot it
again it is going to auto-boot?=true
can any one tell that
what should i do for auto-boot?=false for permanently
thank you in advance (11 Replies)
Hi all,
please i need your help urgently
I am faced to a serious boot disks issue on an Sun Fire E2900.
The system run with two disque in zpool .
The operating system is Solaris 10 (ZFS)
The first time the issue occured, i got the error below on the two disks:
Apr 7 08:04:33... (0 Replies)
In the server room at my new job, there is a V100 with a problem. When power is turned on, the machine goes to the lom prompt. Entering poweron yields an endless supply of this message with no way to break out of it.
**********************************************
PSTATE=0000000000000015... (3 Replies)
Discussion started by: chilinski
3 Replies
LEARN ABOUT OSX
ppmtosixel
ppmtosixel(1) General Commands Manual ppmtosixel(1)NAME
ppmtosixel - convert a portable pixmap into DEC sixel format
SYNOPSIS
ppmtosixel [-raw] [-margin] [ppmfile]
DESCRIPTION
Reads a portable pixmap as input. Produces sixel commands (SIX) as output. The output is formatted for color printing, e.g. for a DEC
LJ250 color inkjet printer.
If RGB values from the PPM file do not have maxval=100, the RGB values are rescaled. A printer control header and a color assignment table
begin the SIX file. Image data is written in a compressed format by default. A printer control footer ends the image file.
OPTIONS -raw If specified, each pixel will be explicitly described in the image file. If -raw is not specified, output will default to com-
pressed format in which identical adjacent pixels are replaced by "repeat pixel" commands. A raw file is often an order of magni-
tude larger than a compressed file and prints much slower.
-margin
If -margin is not specified, the image will be start at the left margin (of the window, paper, or whatever). If -margin is speci-
fied, a 1.5 inch left margin will offset the image.
PRINTING
Generally, sixel files must reach the printer unfiltered. Use the lpr -x option or cat filename > /dev/tty0?.
BUGS
Upon rescaling, truncation of the least significant bits of RGB values may result in poor color conversion. If the original PPM maxval was
greater than 100, rescaling also reduces the image depth. While the actual RGB values from the ppm file are more or less retained, the
color palette of the LJ250 may not match the colors on your screen. This seems to be a printer limitation.
SEE ALSO ppm(5)AUTHOR
Copyright (C) 1991 by Rick Vinci.
26 April 1991 ppmtosixel(1)