08-30-2017
That sounds much more reliable.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
If I give sleep(50) what does it mean?
My program waits for further execution or all my other processes wait? (3 Replies)
Discussion started by: leewar
3 Replies
2. Shell Programming and Scripting
I am in need of some help; think I have confused myself.
Here is the issue I am faced with.
The script log file was fine, the nohup.out file has tens of thousands of lines like illegal use of sleep: sleep seconds
So I assume there is something with the seconds calculation in the script... (1 Reply)
Discussion started by: Glove
1 Replies
3. UNIX for Dummies Questions & Answers
Hi All I have a requiremnt to run a script inside another script.
here i am pulling the record count from the table in oracle.If record count is greater than 0 the script is executed.The scripts updates the count in the table and again the count is found out and the condition is checked and same... (3 Replies)
Discussion started by: dr46014
3 Replies
4. Shell Programming and Scripting
Hi,
Did the sleep command work for hours or only minutes
just give description to work on my script
waiting for the earliest response (5 Replies)
Discussion started by: thelakbe
5 Replies
5. UNIX for Dummies Questions & Answers
sleep 10 &
Is this the write line of command to suspend 5 jobs for 10 minutes (6 Replies)
Discussion started by: senyor17
6 Replies
6. UNIX for Dummies Questions & Answers
Hi Forum
Im using sleep in a while loop goes around 10 times. i feed it a variable with the time i what it to sleep for eg sleep $sleepVal and then print system date and time to screen but sometimes 1 second is added to the time why is this
here my code
sleepVal=5
while
do
... (3 Replies)
Discussion started by: ShinTec
3 Replies
7. Shell Programming and Scripting
Hi All,
i am very new to shall script . i am not that much aware of sleep command ,
i want to terminate the sleep command after certain time.
following is my code.
while
loop
sleep 1800
messag=/status.sql
donethe script will be on sleep untill the messag be comes P. here my requirement... (4 Replies)
Discussion started by: mandlysreedhar
4 Replies
8. Shell Programming and Scripting
Hello,
Need a little help with the script below. I can't get it to sleep :( I'm trying to get this to check if the process is running and if it is, wait 10 secs and check again. Keep doing this until it's not running and then stop checking and send the email.
#!/bin/ksh
mailto=`cat... (2 Replies)
Discussion started by: bbbngowc
2 Replies
9. Shell Programming and Scripting
Hi Frnz,
I need to execute sleep command but i dont know the definite time.
Let me put my req:
I am running one shell script and this script creates some lock file in temp dir ...now in my script i want one function to go into sleep mode till this lock file exists..one lock file gone that... (6 Replies)
Discussion started by: gnnsprapa
6 Replies
10. Shell Programming and Scripting
I need help in script.
I want my one script execute every time at 6:30 am and i have no cron access.
So i am putting sleep command there , Script may took half an hour 35 min , it depend upon queries how much it take time, but that is not issue,
So i want according to stop time of... (15 Replies)
Discussion started by: pallvi_mahajan
15 Replies
LEARN ABOUT HPUX
serialize
serialize(1) General Commands Manual serialize(1)
NAME
serialize - force target process to run serially with other processes
SYNOPSIS
command [command_args]
pid]
DESCRIPTION
The command is used to force the target process to run serially with other processes also marked by this command. The target process can
be referred to by pid value, or it can be invoked directly on the command. Once a process has been marked by the process stays marked
until process completion unless is reissued on the serialized process with the option. The option causes the pid specified with the option
to return to normal timeshare scheduling algorithms.
This call is used to improve process throughput, since process throughput usually increases for large processes when they are executed
serially instead of allowing each program to run for only a short period of time. By running large processes one at a time, the system
makes more efficient use of the CPU as well as system memory, since each process does not end up constantly faulting in its working set, to
only have the pages stolen when another process starts running. As long as there is enough memory in the system, processes marked by
behave no differently from other processes in the system. However, once memory becomes tight, processes marked by are run one at a time
with the highest priority processes being run first. Each process will run for a finite interval of time before another serialized process
is allowed to run.
Options
supports the following options:
Indicates the process specified by
pid should be returned to timeshare scheduling.
Indicates the
pid of the target process.
If neither option is specified, is invoked on the command line passed in.
RETURN VALUE
returns the following value:
Successful completion.
Invalid
pid specification, nonnumeric entry, or pid specification is that of a special system process.
Could not execute the specified command.
No such process.
Must be root or a member of a group having the
privilege to execute
ERRORS
fails under the following condition and sets (see errno(2)) to the following value:
The pid passed in does not exist.
EXAMPLES
Use to force a database application to run serially with other processes marked for serialization:
Force a currently running process with a pid value of 215 to run serially with other processes marked for serialization:
Return a process previously marked for serialization to normal timeshare scheduling. The pid of the target process for this example is
WARNINGS
The user has no way of forcing an execution order on serialized processes.
AUTHOR
was developed by HP.
SEE ALSO
setprivgrp(1M), getprivgrp(2), serialize(2).
serialize(1)