Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Sleep command did not worked
Top Forums UNIX for Beginners Questions & Answers Sleep command did not worked Post 303002651 by mad man on Wednesday 30th of August 2017 03:38:04 AM
Old 08-30-2017
Hi All,

The actual issue was found, the issue what happen is these parallel running scripts are sharing a folder in server to pick the corresponding processing files. At that point of time when these scripts were running the server is 100% busy and even when we have sleep 1 in script the scripts became slow and started to run parallel so the when the second process runs it also picked the file names of first process and its own (first process file name was not suppose to be in there at this point of time). So the second process used the first process file name and failed.

We have planned to pass the file name as argument instead of picking up from shared folder.

Thanks.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

sleep command

If I give sleep(50) what does it mean? My program waits for further execution or all my other processes wait? (3 Replies)
Discussion started by: leewar
3 Replies

2. Shell Programming and Scripting

Sleep Command

I am in need of some help; think I have confused myself. Here is the issue I am faced with. The script log file was fine, the nohup.out file has tens of thousands of lines like illegal use of sleep: sleep seconds So I assume there is something with the seconds calculation in the script... (1 Reply)
Discussion started by: Glove
1 Replies

3. UNIX for Dummies Questions & Answers

sleep command

Hi All I have a requiremnt to run a script inside another script. here i am pulling the record count from the table in oracle.If record count is greater than 0 the script is executed.The scripts updates the count in the table and again the count is found out and the condition is checked and same... (3 Replies)
Discussion started by: dr46014
3 Replies

4. Shell Programming and Scripting

sleep command

Hi, Did the sleep command work for hours or only minutes just give description to work on my script waiting for the earliest response (5 Replies)
Discussion started by: thelakbe
5 Replies

5. UNIX for Dummies Questions & Answers

Help with sleep command

sleep 10 & Is this the write line of command to suspend 5 jobs for 10 minutes (6 Replies)
Discussion started by: senyor17
6 Replies

6. UNIX for Dummies Questions & Answers

sleep command off by a second

Hi Forum Im using sleep in a while loop goes around 10 times. i feed it a variable with the time i what it to sleep for eg sleep $sleepVal and then print system date and time to screen but sometimes 1 second is added to the time why is this here my code sleepVal=5 while do ... (3 Replies)
Discussion started by: ShinTec
3 Replies

7. Shell Programming and Scripting

Sleep command

Hi All, i am very new to shall script . i am not that much aware of sleep command , i want to terminate the sleep command after certain time. following is my code. while loop sleep 1800 messag=/status.sql donethe script will be on sleep untill the messag be comes P. here my requirement... (4 Replies)
Discussion started by: mandlysreedhar
4 Replies

8. Shell Programming and Scripting

Sleep Command

Hello, Need a little help with the script below. I can't get it to sleep :( I'm trying to get this to check if the process is running and if it is, wait 10 secs and check again. Keep doing this until it's not running and then stop checking and send the email. #!/bin/ksh mailto=`cat... (2 Replies)
Discussion started by: bbbngowc
2 Replies

9. Shell Programming and Scripting

Help with sleep command:

Hi Frnz, I need to execute sleep command but i dont know the definite time. Let me put my req: I am running one shell script and this script creates some lock file in temp dir ...now in my script i want one function to go into sleep mode till this lock file exists..one lock file gone that... (6 Replies)
Discussion started by: gnnsprapa
6 Replies

10. Shell Programming and Scripting

Sleep command

I need help in script. I want my one script execute every time at 6:30 am and i have no cron access. So i am putting sleep command there , Script may took half an hour 35 min , it depend upon queries how much it take time, but that is not issue, So i want according to stop time of... (15 Replies)
Discussion started by: pallvi_mahajan
15 Replies

LEARN ABOUT OSX

kill.d

kill.d(1m)							   USER COMMANDS							kill.d(1m)

NAME

       kill.d - snoop process signals as they occur. Uses DTrace.

SYNOPSIS

       kill.d

DESCRIPTION

       kill.d is a simple DTrace program to print details of process signals as they are sent, such as the PID source and destination, signal num-
       ber and result.

       This program can be used to determine which process is sending signals to which other process.

       Since this uses DTrace, only users with root privileges can run this command.

EXAMPLES

       Default output, print process signals as they are sent.
	      # kill.d

FIELDS

       FROM   source PID

       COMMAND
	      source command name

       TO     destination PID

       SIG    destination signal ("9" for a kill -9)

       RESULT result of signal (-1 is for failure)

DOCUMENTATION

       See the DTraceToolkit for further documentation under the Docs directory. The DTraceToolkit docs may include full worked examples with ver-
       bose descriptions explaining the output.

EXIT

       kill.d will run forever until Ctrl-C is hit.

AUTHOR

       Brendan Gregg [Sydney, Australia]

SEE ALSO

       dtrace(1M), truss(1)

version 0.90							   May 14, 2005 							kill.d(1m)
All times are GMT -4. The time now is 10:33 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy