08-10-2017
Could not connect to wireless network
I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..
I tried to open hot spot on my phone and try to connect and it's not connect
I have edumax n150
Try to install new driver - didn't help
Anyone know the problem?
Sent from my SM-J5108 using Tapatalk
8 More Discussions You Might Find Interesting
1. Cybersecurity
At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer??
If I post this in a wrong place, please... (0 Replies)
Discussion started by: him
0 Replies
2. IP Networking
Hi,
I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled.
I can connect to the access point from the laptop, but how do I get the... (1 Reply)
Discussion started by: perleo
1 Replies
3. UNIX for Dummies Questions & Answers
I installed solaris 10 x86 on my dell laptop on a partition alongside windows xp. I am able to connect to the internet in xp with both my ethernet local area connection as well as through my wireless network card. But, however i do not have clue as to how to go about it in solaris.
i did not... (0 Replies)
Discussion started by: stakes20
0 Replies
4. IP Networking
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Discussion started by: rsd220
5 Replies
5. Solaris
hi everyone... this is my first post here
please help me with this..as iam new to solaris
i have installed solaris 10 on virtual box.. and am not able to connect to the internet ..
is there anyway i can get connect to the net..
please help me step by step if possible...
thanks in... (1 Reply)
Discussion started by: yrajendergoud
1 Replies
6. Ubuntu
Hi,
I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
Discussion started by: linux_learner
2 Replies
7. Red Hat
I have managed to install Broadcom BCM43228 Wireless adapter on a laptop running CentOS 5.9 using instructions at:
wiki.centos.org/HowTos/Laptops/Wireless/Broadcom
I had the problem "Error for wireless request "Set Encode" (8B2A): SET failed on device... mentioned on the same page and solved... (0 Replies)
Discussion started by: cooltoad
0 Replies
8. Android
Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
LEARN ABOUT REDHAT
install-netsync
install-netsync(1) General Commands Manual install-netsync(1)
NAME
install-netsync - reads or sets the Network Preferences information on a Palm Device
SYNOPSIS
install-netsync -p /dev/pilot -e -n <hostname> -i <ip> -m <netmask>
DESCRIPTION
install-netsync allows the user to read or change the Network Preferences stored on the Pilot
OPTIONS
-p --port <port>,
Use device file port to communicate with the Palm handheld device. If this is not specified, will look for the $PILOTPORT environ-
ment variable. If both are not found, will fall back to /dev/pilot.
-h --help
Display help synopsis for install-netsync
-v --version
Display version of install-netsync
-e --enable
Enable the LanSync operation (instead of local HotSync)
-n --name <hostname>,
Sets the hostname of the remote machine you wish to connect to. This is not the hostname of the Palm device itself
-i --ip
Set the IP address of the remote machine you wish to connect to. This is not the IP address of the Palm device itself
-m --mask
Set the netmask of the remote machine you wish to connect to. This is not the netmask address of the Palm device itself
USAGE
The program will connect to a target Palm handheld device, and read or set the Network Preferences information specified or display the
Network Preferences stored on the Palm device
KNOWN BUGS
install-netsync has no known bugs.
REPORTING BUGS
Report bugs at http://bugs.pilot-link.org/
AUTHOR
install-netsync was created from the original install-user
application originally written by D. Jeff Dionne <jeff@RyeHam.ee.ryerson.ca>, and was split it out into a separate conduit by JP Rosevear
<jpr@ximian.com>
Free Software Foundation Palm Computing Device Tools install-netsync(1)