Sponsored Content
Operating Systems Solaris Fresh Install - Boot Load Failed Post 303001649 by DukeNuke2 on Tuesday 8th of August 2017 12:30:45 PM
Old 08-08-2017
Make sure you are using the latest Solaris 10 release (01/13). Older releases won't work with a M10 system.
These 2 Users Gave Thanks to DukeNuke2 For This Post:
 

9 More Discussions You Might Find Interesting

1. HP-UX

11.0 fresh install: I never see CDE Login

I've just completed a fresh install of HP-UX 11.0 on my 712/80 and everything starts up fine until it gets to the point where X kicks off and I believe at this point is supposed to launch into the CDE login. It just sits there on the blank X screen with the X cursor for a minute or so then BEEPS... (9 Replies)
Discussion started by: ErikTheHAck
9 Replies

2. Solaris

boot load failed

I modified the partitions on my Solaris 10 disk using format command in "boot cdrom -s" mode and then tried rebooting with "reboot". It said "Boot load failed". Why does this happen? I have faced this error before:( and I went in for a fresh installation of the OS.Can anyone tell me the reason as... (1 Reply)
Discussion started by: lydiaEd
1 Replies

3. AIX

Root password for fresh 5.1 install on 43p-140?

I've installed AIX 5.1 on a 43p-140, but am unable to log in. At no point in the install did it ask me for a root password. When it boots to the console prompt, I enter "root" as a username, and then after 1 second it cycles right back to another root prompt. I am accessing the 43p-140... (4 Replies)
Discussion started by: akbar
4 Replies

4. Solaris

Only LAN access after fresh install

Hello, For whatever reason, after installing Solaris 10 I can ping anything within my own LAN, including the router which is also set as the default gateway, but I have no internet connectivity with it. At first I thought this was a DNS issue, but I can't connect with external IP addresses... (3 Replies)
Discussion started by: Quadratic
3 Replies

5. Solaris

Fresh install of solaris 10 using an ISO

Hi all Im rebuilding an 6800 domain with solaris 10. Server is located in a different town and cant be bothered to drive down and install a dvd into its drive. So, apart from jumpstarting it and using a local DVD, is there a way I can an ISO image to build a new client ?? eg. mount an ISO... (2 Replies)
Discussion started by: sbk1972
2 Replies

6. Solaris

M5000 boot net- install failed

Good evening all,I'm new to your site, so please bear any infringements or transgressions on my part.I'm new to the whole Solaris boot install over the net scenario, but here's where I'm stuck:I have an M5000 with 2 domains (running unimode). Domain 0 is configured and running Solaris 10. Domain 1... (9 Replies)
Discussion started by: RandomSun
9 Replies

7. Solaris

Solaris 8 fresh install halts

Installing Solaris 8 for the first time...on a SunBlade 100. I have original Solaris 8 CD's. About 45 minutes into the installation, the install halts with the following errors: ERROR: Could not open file /a/etc/vfstab ERROR: Could not create the file system mount table /etc/vfstab I... (4 Replies)
Discussion started by: cdunavent
4 Replies

8. AIX

ISCSI poor performance 1.5MB/s fresh install AIX7.1

Hi Everyone, I have been struggling for few days with iSCSI and thought I could get some help on the forum... fresh install of AIX7.1 TL4 on Power 710, The rootvg relies on 3 SAS disks in RAID 0, 32GB Memory The lpar Profile is using all of the managed system's resources. I have connected... (11 Replies)
Discussion started by: frenchy59
11 Replies

9. Debian

Debian fresh install blinking cursor meaning?

Hello, I have downloaded and install debian in computer it is blinking cursor what this mean? (6 Replies)
Discussion started by: Riteshkakkar
6 Replies
devfree(1M)						  System Administration Commands					       devfree(1M)

NAME
devfree - release devices from exclusive use SYNOPSIS
devfree key [device...] DESCRIPTION
devfree releases devices from exclusive use. Exclusive use is requested with the command devreserv. When devfree is invoked with only the key argument, it releases all devices that have been reserved for that key. When called with key and device arguments, devfree releases the specified devices that have been reserved with that key. OPERANDS
The following operands are supported: device Defines device that this command will release from exclusive use. device can be the pathname of the device or the device alias. key Designates the unique key on which the device was reserved. EXIT STATUS
The following exit values are returned: 0 Successful completion. 1 Command syntax was incorrect, an invalid option was used, or an internal error occurred. 2 Device table or device reservation table could not be opened for reading. 3 Reservation release could not be completely fulfilled because one or more of the devices was not reserved or was not reserved on the specified key. FILES
/etc/device.tab /etc/devlkfile ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ SEE ALSO
devreserv(1M), attributes(5) NOTES
The commands devreserv and devfree are used to manage the availability of devices on a system. These commands do not place any con- straints on the access to the device. They serve only as a centralized bookkeeping point for those who wish to use them. Processes that do not use devreserv may concurrently use a device with a process that has reserved that device. SunOS 5.10 5 Jul 1990 devfree(1M)
All times are GMT -4. The time now is 08:30 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy