I've just completed a fresh install of HP-UX 11.0 on my 712/80 and everything starts up fine until it gets to the point where X kicks off and I believe at this point is supposed to launch into the CDE login.
It just sits there on the blank X screen with the X cursor for a minute or so then BEEPS... (9 Replies)
I modified the partitions on my Solaris 10 disk using format command in "boot cdrom -s" mode and then tried rebooting with "reboot". It said "Boot load failed".
Why does this happen?
I have faced this error before:( and I went in for a fresh installation of the OS.Can anyone tell me the reason as... (1 Reply)
I've installed AIX 5.1 on a 43p-140, but am unable to log in. At no point in the install did it ask me for a root password. When it boots to the console prompt, I enter "root" as a username, and then after 1 second it cycles right back to another root prompt.
I am accessing the 43p-140... (4 Replies)
Hello,
For whatever reason, after installing Solaris 10 I can ping anything within my own LAN, including the router which is also set as the default gateway, but I have no internet connectivity with it. At first I thought this was a DNS issue, but I can't connect with external IP addresses... (3 Replies)
Hi all
Im rebuilding an 6800 domain with solaris 10. Server is located in a different town and cant be bothered to drive down and install a dvd into its drive.
So, apart from jumpstarting it and using a local DVD, is there a way I can an ISO image to build a new client ?? eg. mount an ISO... (2 Replies)
Good evening all,I'm new to your site, so please bear any infringements or transgressions on my part.I'm new to the whole Solaris boot install over the net scenario, but here's where I'm stuck:I have an M5000 with 2 domains (running unimode). Domain 0 is configured and running Solaris 10. Domain 1... (9 Replies)
Installing Solaris 8 for the first time...on a SunBlade 100. I have original Solaris 8 CD's.
About 45 minutes into the installation, the install halts with the following errors:
ERROR: Could not open file /a/etc/vfstab
ERROR: Could not create the file system mount table /etc/vfstab
I... (4 Replies)
Hi Everyone,
I have been struggling for few days with iSCSI and thought I could get some help on the forum...
fresh install of AIX7.1 TL4 on Power 710, The rootvg relies on 3 SAS disks in RAID 0, 32GB Memory
The lpar Profile is using all of the managed system's resources.
I have connected... (11 Replies)
Hello,
I have downloaded and install debian in computer it is blinking cursor what this mean? (6 Replies)
Discussion started by: Riteshkakkar
6 Replies
LEARN ABOUT OSF1
sys_attrs_pci
sys_attrs_pci(5) File Formats Manual sys_attrs_pci(5)NAME
sys_attrs_pci - pci subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the PCI (pci) kernel subsystem. Refer to the sys_attrs(5) reference page for an
introduction to the topic of kernel subsystem attributes.
For this subsytem, users should modify only the following attribute and do so only for the purpose described. Any other visible attributes
cannot or should not be modified.
A bit-mask setting that allows the developer of PCI hardware and softwareto determine the PCI configuration parameters on an Alpha
system based on the PCI bus. By setting PCI_Developer_Debug to different values, a variety of hardware-related or software-related
information about all PCI devices on an AlphaServer are printed out at system bootstrap time. If loadable drivers are used, loadable
configuration data is also printed out on execution of the sysconfig -c command.
Refer to the /usr/include/io/dec/pci/pci_debug.h file for valid bit-field settings for this attribute. The pci_debug.h file con-
tains macro definitions that state the type of information that is printed out if PCI_Developer_Debug is set to a particular value.
Any combination of the bit-flags is valid. For example, the value 0x70 allows the hardware or software developer to see the PCI
configuration header information that the kernel reads or assigns to PCI devices.
Default value: 0
Minimum value: 0
Maximum value: FFFFFFFF(16)SEE ALSO sys_attrs(5)
Writing PCI Bus Device Drivers
sys_attrs_pci(5)