Sponsored Content
Operating Systems Solaris How to identify if disk is attached to SAN and assist in migration.? Post 303001531 by kpatel786 on Sunday 6th of August 2017 03:26:24 PM
Old 08-06-2017
Code:
DEVICE PROPERTIES for disk: /dev/rdsk/c3t60060480000290101499533030374535d0s2
  Vendor:               EMC
  Product ID:           SYMMETRIX
  Revision:             5773
  Serial Num:           1014997E5000
  Unformatted capacity: 43157.812 MBytes
  Read Cache:           Enabled
    Minimum prefetch:   0x0
    Maximum prefetch:   0xffff
  Device Type:          Disk device
  Path(s):

  /dev/rdsk/c3t60060480000290101499533030374535d0s2
  /devices/scsi_vhci/ssd@g60060480000290101499533030374535:c,raw
   Controller           /devices/pci@780/pci@0/pci@8/SUNW,qlc@0/fp@0,0
    Device Address              5006048452a63ec9,60
    Host controller port WWN    2100001b3212ffda
    Class                       primary
    State                       ONLINE
   Controller           /devices/pci@7c0/pci@0/pci@9/SUNW,qlc@0/fp@0,0
    Device Address              5006048452a63ec6,60
    Host controller port WWN    2100001b3212ccdb
    Class                       primary
    State                       ONLINE

The above command show to paths from two different HBA,s it is similar to other devices as well.

This is a VM host the vfstab output is
Code:
cat /etc/vfstab
#device         device          mount           FS      fsck    mount   mount
#to mount       to fsck         point           type    pass    at boot options
#
fd      -       /dev/fd fd      -       no      -
/proc   -       /proc   proc    -       no      -
/dev/dsk/c1t0d0s1       -       -       swap    -       no      -
/dev/dsk/c1t0d0s0       /dev/rdsk/c1t0d0s0      /       ufs     1       no      logging
/dev/dsk/c1t0d0s3       /dev/rdsk/c1t0d0s3      /var    ufs     1       no      logging
/dev/dsk/c1t0d0s4       /dev/rdsk/c1t0d0s4      /home   ufs     2       yes     logging
/dev/dsk/c1t0d0s5       /dev/rdsk/c1t0d0s5      /var/crash      ufs     2       yes     logging
/devices        -       /devices        devfs   -       no      -
sharefs -       /etc/dfs/sharetab       sharefs -       no      -
ctfs    -       /system/contract        ctfs    -       no      -
objfs   -       /system/object  objfs   -       no      -
swap    -       /tmp    tmpfs   -       yes     -

I am planning to do online storage migration following below steps, it has one ldom.
  1. Remove 1 fc
  2. Assign the luns from the new storage
  3. scan the devices
  4. Mirror it ( dont know the command )
  5. Break the mirror and remove the old storage lun
  6. attach the 2nd fc.

Will this work ?

Last edited by rbatte1; 08-07-2017 at 08:22 AM.. Reason: Converted textual numbers list to formatted numbered list with LIST=1 tags
 

10 More Discussions You Might Find Interesting

1. HP-UX

SAN migration

Hi, I'm going to be involved in a migration of SAN islands to one big SAN. I've not worked with SANs before and I'm not sure how to approach this. I suspect the disk devices on the HP servers are going to change, when the EVA's and servers are plugged into this new Cisco 9509 switch. Any... (0 Replies)
Discussion started by: Hils
0 Replies

2. Solaris

SAN connection - configuring fibre attached hard drive

Hi All, I recently got a connection to the SAN through a fibre channel on my solaris box: #luxadm -e port /devices/pci@1d,700000/SUNW,qlc@1/fp@0,0:devctl CONNECTED #ls -l /dev/cfg lrwxrwxrwx 1 root root 48 Feb 23 12:31 c4 -> ../../devices/pci@1d,700000/SUNW,qlc@1/fp@0,0:fc I then... (2 Replies)
Discussion started by: dede
2 Replies

3. Red Hat

Identify SAN disks not in use

Hello, How can I identify SAN disks not in use by the OS? Thank you. (8 Replies)
Discussion started by: asanchez
8 Replies

4. Solaris

Identify Boot from SAN

How to identify the server is BOOT FROM SAN. Also how one can find from which device it is booted? Thanks Rahul Double post, continued here (0 Replies)
Discussion started by: rahul.kurumkar
0 Replies

5. Red Hat

Identify Boot from SAN

Hi, I have many servers all of these are boot from SAN. Can anybody let me know that how to identify the server is Boot fron SAN and from which device? Thanks Rahul (1 Reply)
Discussion started by: rahul.kurumkar
1 Replies

6. HP-UX

SAN Migration of HP-UX hosts

Hello gurus, I am a SAN Admin - not very familiar with the HPUX administration - so need help with the steps in regards to the migration I need to do at my client place. Environment: Migrating from CX4 to VMAX - using OR/Hot Pull. Here are the steps I have put together - HPUX gurus please... (5 Replies)
Discussion started by: jps460
5 Replies

7. AIX

SAN Migration

Hi all, We are migrating our SAN storage from HSV360 to 3PAR. The system runs aix 6.1 version with HACMP. Please let me know what are requirements from OS side and how are the data copied to the new disks. (10 Replies)
Discussion started by: ElizabethPJ
10 Replies

8. HP-UX

SAN Migration question

Hi, I am very new to HP-UX, and we're going to be doing a SAN migration. We're going to take down the machine, and zone it to the new SAN. My question is, will the device names change and will that interfere with the LVM? If the new disks come in with different device names, how would I... (3 Replies)
Discussion started by: BG_JrAdmin
3 Replies

9. AIX

AIX - FC Switch migration, SAN Migration question!

I'm New to AIX / VIOS We're doing a FC switch cutover on an ibm device, connected via SAN. How do I tell if one path to my remote disk is lost? (aix lvm) How do I tell when my link is down on my HBA port? Appreciate your help, very much! (4 Replies)
Discussion started by: BG_JrAdmin
4 Replies

10. Linux

Identify newly attached LUN from NetApp

Hi I need to identify a newly attached LUN from NetApp on a linuxserver running uname -o GNU/Linux I have first run the df -h and got the following: df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_outsystemdb-lv_root 50G 2.7G 45G ... (3 Replies)
Discussion started by: fretagi
3 Replies
disks(1M)						  System Administration Commands						 disks(1M)

NAME
disks - creates /dev entries for hard disks attached to the system SYNOPSIS
/usr/sbin/disks [-C] [-r rootdir] DESCRIPTION
devfsadm(1M) is now the preferred command for /dev and should be used instead of disks. disks creates symbolic links in the /dev/dsk and /dev/rdsk directories pointing to the actual disk device special files under the /devices directory tree. It performs the following steps: 1. disks searches the kernel device tree to see what hard disks are attached to the system. It notes the /devices pathnames for the slices on the drive and determines the physical component of the corresponding /dev/dsk or /dev/rdsk name. 2. The /dev/dsk and /dev/rdsk directories are checked for disk entries - that is, symbolic links with names of the form cN[tN]dNsN, or cN[tN]dNpN, where N represents a decimal number. cN is the logical controller number, an arbitrary number assigned by this program to designate a particular disk controller. The first controller found on the first occasion this program is run on a system, is assigned number 0. tN is the bus-address number of a subsidiary controller attached to a peripheral bus such as SCSI or IPI (the target number for SCSI, and the facility number for IPI controllers). dN is the number of the disk attached to the controller. sN is the slice number on the disk. pN is the FDISK partition number used by fdisk(1M). (x86 Only) 3. If only some of the disk entries are found in /dev/dsk for a disk that has been found under the /devices directory tree, disks creates the missing symbolic links. If none of the entries for a particular disk are found in /dev/dsk, disks checks to see if any entries exist for other disks attached to the same controller, and if so, creates new entries using the same controller number as used for other disks on the same controller. If no other /dev/dsk entries are found for slices of disks belonging to the same physical con- troller as the current disk, disks assigns the lowest-unused controller number and creates entries for the disk slices using this newly-assigned controller number. disks is run automatically each time a reconfiguration-boot is performed or when add_drv(1M) is executed. When invoking disks(1M) manually, first run drvconfig(1M) to ensure /devices is consistent with the current device configuration. Notice to Driver Writers disks considers all devices with a node type of DDI_NT_BLOCK, DDI_NT_BLOCK_CHAN, DDI_NT_CD, DDI_NT_BLOCK_WWN or DDI_NT_CD_CHAN to be disk devices. disks(1M) requires the minor name of disk devices obey the following format conventions. The minor name for block interfaces consists of a single lowercase ASCII character, a through u. The minor name for character (raw) inter- faces consists of a single lowercase ASCII character, a through u, followed by ,raw. disks translates a through p to s0 through s15, while it translates q through u to p0 through p4. SPARC drivers should only use the first 8 slices: a through h, while x86 drivers can use a through u, with q through u corresponding to fdisk(1M) partitions. q represents the entire disk, while r, s, t, and u represent up to 4 additional partitions. To prevent disks from attempting to automatically generate links for a device, drivers must specify a private node type and refrain from using a node type: DDI_NT_BLOCK, DDI_NT_BLOCK_CHAN, DDI_NT_CD, or DDI_NT_CD_CHAN when calling ddi_create_minor_node(9F). OPTIONS
The following options are supported: -C Causes disks to remove any invalid links after adding any new entries to /dev/dsk and /dev/rdsk. Invalid links are links which refer to non-existent disk nodes that have been removed, powered off, or are otherwise inaccessible. -r rootdir Causes disks to presume that the /dev/dsk, /dev/rdsk and /devices directory trees are found under rootdir, not directly under /. ERRORS
If disks finds entries of a particular logical controller linked to different physical controllers, it prints an error message and exits without making any changes to the /dev directory, since it cannot determine which of the two alternative logical-to-physical mappings is correct. The links should be manually corrected or removed before another reconfiguration-boot is performed. EXAMPLES
Example 1: Creating Block and Character Minor Devices The following example demonstrates creating the block and character minor devices from within the xkdisk driver's attach(9E) function. #include <sys/dkio.h> /* * Create the minor number by combining the instance number * with the slice number. */ #define MINOR_NUM(i, s) ((i) << 4 | (s)) int xkdiskattach(dev_info_t *dip, ddi_attach_cmd_t cmd) { int instance, slice; char name[8]; /* other stuff in attach... */ instance = ddi_get_instance(dip); for (slice = 0; slice < V_NUMPAR; slice++) { /* * create block device interface */ sprintf(name, "%c", slice + 'a'); ddi_create_minor_node(dip, name, S_IFBLK, MINOR_NUM(instance, slice), DDI_NT_BLOCK_CHAN, 0); /* * create the raw (character) device interface */ sprintf(name,"%c,raw", slice + 'a'); ddi_create_minor_node(dip, name, S_IFCHR, MINOR_NUM(instance, slice), DDI_NT_BLOCK_CHAN, 0); } } Installing the xkdisk disk driver on a Sun Fire 4800, with the driver controlling a SCSI disk (target 3 attached to an isp(7D) SCSI HBA) and performing a reconfiguration-boot (causing disks to be run) creates the following special files in /devices. # ls -l /devices/ssm@0,0/pci@18,700000/pci@1/SUNW,isptwo@4/ brw-r----- 1 root sys 32, 16 Aug 29 00:02 xkdisk@3,0:a crw-r----- 1 root sys 32, 16 Aug 29 00:02 xkdisk@3,0:a,raw brw-r----- 1 root sys 32, 17 Aug 29 00:02 xkdisk@3,0:b crw-r----- 1 root sys 32, 17 Aug 29 00:02 xkdisk@3,0:b,raw brw-r----- 1 root sys 32, 18 Aug 29 00:02 xkdisk@3,0:c crw-r----- 1 root sys 32, 18 Aug 29 00:02 xkdisk@3,0:c,raw brw-r----- 1 root sys 32, 19 Aug 29 00:02 xkdisk@3,0:d crw-r----- 1 root sys 32, 19 Aug 29 00:02 xkdisk@3,0:d,raw brw-r----- 1 root sys 32, 20 Aug 29 00:02 xkdisk@3,0:e crw-r----- 1 root sys 32, 20 Aug 29 00:02 xkdisk@3,0:e,raw brw-r----- 1 root sys 32, 21 Aug 29 00:02 xkdisk@3,0:f crw-r----- 1 root sys 32, 21 Aug 29 00:02 xkdisk@3,0:f,raw brw-r----- 1 root sys 32, 22 Aug 29 00:02 xkdisk@3,0:g crw-r----- 1 root sys 32, 22 Aug 29 00:02 xkdisk@3,0:g,raw brw-r----- 1 root sys 32, 23 Aug 29 00:02 xkdisk@3,0:h crw-r----- 1 root sys 32, 23 Aug 29 00:02 xkdisk@3,0:h,raw /dev/dsk will contain the disk entries to the block device nodes in /devices # ls -l /dev/dsk /dev/dsk/c0t3d0s0 -> ../../devices/[...]/xkdisk@3,0:a /dev/dsk/c0t3d0s1 -> ../../devices/[...]/xkdisk@3,0:b /dev/dsk/c0t3d0s2 -> ../../devices/[...]/xkdisk@3,0:c /dev/dsk/c0t3d0s3 -> ../../devices/[...]/xkdisk@3,0:d /dev/dsk/c0t3d0s4 -> ../../devices/[...]/xkdisk@3,0:e /dev/dsk/c0t3d0s5 -> ../../devices/[...]/xkdisk@3,0:f /dev/dsk/c0t3d0s6 -> ../../devices/[...]/xkdisk@3,0:g /dev/dsk/c0t3d0s7 -> ../../devices/[...]/xkdisk@3,0:h and /dev/rdsk will contain the disk entries for the character device nodes in /devices # ls -l /dev/rdsk /dev/rdsk/c0t3d0s0 -> ../../devices/[...]/xkdisk@3,0:a,raw /dev/rdsk/c0t3d0s1 -> ../../devices/[...]/xkdisk@3,0:b,raw /dev/rdsk/c0t3d0s2 -> ../../devices/[...]/xkdisk@3,0:c,raw /dev/rdsk/c0t3d0s3 -> ../../devices/[...]/xkdisk@3,0:d,raw /dev/rdsk/c0t3d0s4 -> ../../devices/[...]/xkdisk@3,0:e,raw /dev/rdsk/c0t3d0s5 -> ../../devices/[...]/xkdisk@3,0:f,raw /dev/rdsk/c0t3d0s6 -> ../../devices/[...]/xkdisk@3,0:g,raw /dev/rdsk/c0t3d0s7 -> ../../devices/[...]/xkdisk@3,0:h,raw FILES
/dev/dsk/* Disk entries (block device interface) /dev/rdsk/* Disk entries (character device interface) /devices/* Device special files (minor device nodes) ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ SEE ALSO
add_drv(1M), devfsadm(1M), fdisk(1M), attributes(5), isp(7D), devfs(7FS), dkio(7I), attach(9E), ddi_create_minor_node(9F) Writing Device Drivers BUGS
disks silently ignores malformed minor device names. SunOS 5.10 7 Nov 2002 disks(1M)
All times are GMT -4. The time now is 03:04 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy