Hi ,
I want to change the order of a string using sed command . Is it possible ?
$echo "abc123xyz" | sed 's/\()*\) \(*\)/\2\1/'
abc123xyz
$ echo "abc123xyz" |sed 's/\()*\) \(*\) \()*\)/\2\1\3/'
abc123xyz
I want to change the string ,
abc123xyz as
xyz123abc .
Is it... (5 Replies)
Hi everyone,
Please some help over here. (I´m using cygwing)
I have files with 40 columns and 2000 lines in average. I´m trying to change the order position as follow.
Original columns position:... (3 Replies)
Good evening
I have a file as below and want to change the order, as in the second column, sed awk Pearl
Thanks
aaaaaaaaaa
bbbbbbbbb
cccccccc
aaaaaaaaaa
bbbbbbbbb
cccccccc
aaaaaaaaaa
cccccccc
bbbbbbbbb
aaaaaaaaaa
cccccccc
bbbbbbbbb (8 Replies)
i need a script that reads a wwn file like this:
LOCAL_HOST (before)
50:01:24:82:00:6c:a9:04
21:00:00:24:ff:30:35:7b
21:00:00:24:ff:30:35:70and will run over the file with all the wwn's in the same row in order to create zones on a switch
like so:
LOCAL_HOST (after)
zonecreate " (... (2 Replies)
hi guys
I have a service that depends on some shares (NFS shares ) that need to be mounted before before the service start so the service-app finds the NFS shares and starts correctly...
I am confused here this is what I found but I am not sure what to do in order to change it
BTW is Suse... (2 Replies)
I have this END section in an awk script:
END {
for (j in littlebin)
{
print (j, int(log(j)/log(2)) , littlebin)
lbsum+=littlebin
}
for (i in bins)
... (6 Replies)
Hi All
I have a file like this:
ID1 ref_A 10 ref_B 30 ref_C 5
ID2 ref_F 69 ref_G 12 ref_H 5
Every ID is followed by a string(ref_X) followed by a number(every number is referred to the previous ref)
I would like to order the file like this(the column could be more, but always with the same... (4 Replies)
Hi everyone,
What is the best solution to check every line in the xml file and change order of found field along with its value without touching value. Pattern will be given i.e. one line can look like this one:
<widget position="value,value" size="value,value" name="value"... (5 Replies)
Hello,
I am trying to replace the position of each row by the next row.
OS: Ubuntu 18.04, bionic
I'd appreciate your help.
input_file:
-O fileA
wget http://x.y.z./a
-O fileB
wget http://a.b.c./d
-O fileC
wget http://q.f.s/t
..
..
..
-O fileZZ
wget http://r.t.y/u
I expect: (6 Replies)
Discussion started by: baris35
6 Replies
LEARN ABOUT V7
vp
VP(4) Kernel Interfaces Manual VP(4)NAME
vp - Versatec printer-plotter
DESCRIPTION
Vp0 is the interface to a Versatec D1200A printer-plotter with a Versatec C-PDP11(DMA) controller. Ordinarily bytes written on it are
interpreted as ASCII characters and printed. As a printer, it writes 64 lines of 132 characters each on 11 by 8.5 inch paper. Only some
of the ASCII control characters are interpreted.
NL performs the usual new-line function, i.e. spaces up the paper and resets to the left margin. It is ignored however following a CR
which ends a non-empty line.
CR is ignored if the current line is empty but is otherwise like NL.
FF resets to the left margin and then to the top of the next page.
EOT resets to the left margin, advances 8 inches, and then performs a FF.
The ioctl(2) system call may be used to change the mode of the device. Only the first word of the 3-word argument structure is used. The
bits mean:
0400 Enter simultaneous print/plot mode.
0200 Enter plot mode.
0100 Enter print mode (default on open).
040 Send remote terminate.
020 Send remote form-feed.
010 Send remote EOT.
04 Send remote clear.
02 Send remote reset.
On open a reset, clear, and form-feed are performed automatically. Notice that the mode bits are not encoded, so that it is required that
exactly one be set.
In plot mode each byte is interpreted as 8 bits of which the high-order is plotted to the left; a `1' leaves a visible dot. A full line of
dots is produced by 264 bytes; lines are terminated only by count or by a remote terminate function. There are 200 dots per inch both ver-
tically and horizontally.
When simultaneous print-plot mode is entered exactly one line of characters, terminated by NL, CR, or the remote terminate function, should
be written. Then the device enters plot mode and at least 20 lines of plotting bytes should be sent. As the line of characters (which is
20 dots high) is printed, the plotting bytes overlay the characters. Notice that it is impossible to print characters on baselines that
differ by fewer than 20 dot-lines.
In print mode lines may be terminated either with an appropriate ASCII character or by using the remote terminate function.
FILES
/dev/vp0
SEE ALSO opr(1)VP(4)