There are two servers which needs to be connected via the port number 1521 from a remote server.
This is the port config in the first server : L28tstream1 :
This is the port config in the 2nd server : L28stream2 :
As you can see, the way the port is open in both the servers above is different. For the first server, the port is stated with the ip address, whereas for the 2nd one this is not the case.
Also for the first server, the "Foreign Address" column displays as 0.0.0.0:* whereas for the 2nd one it just has some dots like :::*.
How are the lines above configured for each server to look like how they look above? What do the differences mean? What do the dots indicate?
/* Linux Slackware */
Nmap shows the following ports open on the gateway.
21/tcp ftp
22/tcp ssh
23/tcp telnet
25/tcp smtp
37/tcp time
80/tcp http
113/tcp auth
515/tcp printer
587/tcp submission
1024/tcp kdm
6000/tcp x11
-------------------------------
i would like to close as... (10 Replies)
Hi, I'm trying to fix up some serial code that was given to me by a coworker no longer on the project. Problem is, when the program is running and reading the port, I can take away the port by doing a cu command in another terminal window. When I release the cu, the program crashes, I think... (1 Reply)
hi all
1) how to determine available ports in a box (solaris)
do i have to go for a netstat on all the ports?
2) how to block a particular port for a particular type of connection.
Any help would be greatly appreciated
Thanks (7 Replies)
Hello, i need a script (bash type maybe?..), which would check open ports on 127.0.0.1 and then compare open ports with "registered/allowed" port list and try to kill the program who uses unregistered ports. It would be great that script would be started lets say every 5 or 10 minutes.
You see i... (2 Replies)
hi guys,
may i know the exact steps to open a port in solaris.i have some rough idea - which is adding the port number in /etc/services.
but i am not sure the correct conventions, steps or any other steps.
kindly advise.thanks guys ! (1 Reply)
just a quick question:
a. whats the simplest command to check open port and the corresponding services?
example:
bash-2.05# netstat -an | grep LISTEN
*.199 *.* 0 0 49152 0 LISTEN
*.8989 *.* 0 0 49152 ... (1 Reply)
Hi,
I have read some forum theads about the open and close ports. some points are clear and it is not working on my machine or something am i missing?
I have commented out a port /etc/services, one application uses
then when i use the telnet <hostname> <port_blocked> it shows connected..... (1 Reply)
Discussion started by: balamv
1 Replies
LEARN ABOUT OSF1
port_names
ports(7) Miscellaneous Information Manual ports(7)NAME
ports, port_names - Device (tty and lp) names for serial and parallel ports
SYNOPSIS
Default Serial Ports:
/dev/tty00
/dev/tty01 (not present on a single-port system)
Parallel Port:
/dev/lp0
DESCRIPTION
AlphaStation and AlphaServer systems provide one or two 9-pin serial communication ports. These ports are usually labelled 1 (COMM1) and 2
(COMM2), but they may be identified by different icons. Using the appropriate serial cable and terminator, you can connect a serial
printer, external modem, or character-cell terminal to a serial port. Most AlphaStation and AlphaServer systems also provide one parallel
port, for use with a parallel printer.
When you add a device to your system, the installation documentation may instruct you to map the device pathname to the port. These
devices are located in the /dev directory.
For serial-line ports, the two default device pathnames are: This pathname always maps to 1, COMM1, the lowest port number, an icon for a
terminal console, or the only serial port (on a single-port system). This pathname always maps to 2, COMM2, the next numbered port, or (if
one serial port is labeled with an icon for a terminal console) the remaining serial port.
If your system hardware has been extended to include additional serial ports, the pathnames /dev/tty02, /dev/tty03, and so forth, may also
be available to you. However, most systems have only /dev/tty00 and /dev/tty01 as the device pathnames for serial ports.
The one parallel port on an AlphaStation or AlphaServer may be labeled with the word printer or a printer icon. On some systems, the paral-
lel port may not be labeled. The device pathname for the parallel port is /dev/lp0. Currently, Tru64 UNIX does not fully support parallel
printers, so fewer devices are connected to this port as compared to serial ports.
If you are connecting a terminal console to your system, it must be connected to the serial port mapped to /dev/tty00. For other serial
devices, it does not matter which of the serial ports you choose for the connection. For example, suppose you are setting up a system that
has two serial ports, labeled 1 and 2. You intend to use a serial-line terminal rather than a workstation monitor as the system console and
also want to connect a serial-line printer to the system. In this case, you must connect the terminal to the port labeled 1 (with the
device pathname /dev/tty00). Therefore, you must connect the printer to the remaining port labeled 2 (with the device pathname /dev/tty01).
If, for the same type of system, you intend to use a workstation monitor as the system console, it does not matter which serial port you
use for a serial-line printer or modem. In other words, you can connect the printer to either port 1 (with pathname /dev/tty00) or port 2
(with pathname /dev/tty01). When prompted to enter a /dev/tty** pathname by the lprsetup script or the Print configuration tool in the CDE
Application Manager, you would specify /dev/tty00 if you connected the printer to port 1 or /dev/tty01 if you connected the printer to port
2.
See the System Administration manual for more information on setting up consoles (including remote consoles) and printers. See the
modem(7) reference page for more information on setting up modems.
SEE ALSO
Commands: lprsetup(8)
Devices: ace(7), modem(7)
System Administration delim off
ports(7)