|
|
Sponsored Content
Operating Systems
AIX
How to change from tty03 to tty00 serial port in AIX 5.x?
Post 302998914 by trevian3969 on Friday 9th of June 2017 01:41:55 PM
06-09-2017
Yes, I was wrong about the state. 2 were available and 2 were Defined.
What I did is delete all ttys, and then add one by one.
Because Im new in AIX, I used SMIT utility.
Now I have this partially resolved, I have one last question.
The connection is as follows:
GPS sends info from a serial port to a serial port from Server with AIX.
We connect a laptop using hyperterminal to the serial port from the GPS and confirm that the GPS sends information.
It is possible to see if the serial port from the server are receiving the same info from the GPS ?
Thanks again
What I did is delete all ttys, and then add one by one.
Because Im new in AIX, I used SMIT utility.
Now I have this partially resolved, I have one last question.
The connection is as follows:
GPS sends info from a serial port to a serial port from Server with AIX.
We connect a laptop using hyperterminal to the serial port from the GPS and confirm that the GPS sends information.
It is possible to see if the serial port from the server are receiving the same info from the GPS ?
Thanks again
|
|
10 More Discussions You Might Find Interesting
1. Programming
Hai there,
Can any one provide me with a ansi c source code for
opening com1 or com2 and read data. The port is connected to
another serial communication device on rs232 port.
The o/s is Sco Unix 5.0.6
Matter urgent
Viswanath (0 Replies)
Discussion started by: viswanath
0 Replies
2. Solaris
hi
i am using solaris 9 on sparc .
i was wondering if there was a command to control my serial interface , as to send a signal periodically every interval of time to the input of a 555 timer .
thanks for your help .... (0 Replies)
Discussion started by: ppass
0 Replies
3. Solaris
Hi,
I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port.
When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Discussion started by: smartgupta
1 Replies
4. Programming
Hello!
Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements:
1. Serial port is opened in non-canonical mode.
2. All the time I need to check is there something to read.
3. If I have to write something I need to write it... (6 Replies)
Discussion started by: jvrlic
6 Replies
5. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
6. Solaris
What is the serial port on the T5140 used for. (4 Replies)
Discussion started by: pgsanders
4 Replies
7. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
8. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
9. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
10. AIX
HI,
Does anyone installed a GPS from his Serial port to an IBM Server serial port with AIX 5.X
I would like the rs232 configuration you used on the GPS, and the ttys configuration from your server.
Thanks in advance !!! (8 Replies)
Discussion started by: trevian3969
8 Replies
LEARN ABOUT DEBIAN
snnewgroup
snnewgroup.v0.3.8(8) System Manager's Manual snnewgroup.v0.3.8(8) NAME
snnewgroup - create a new sn newsgroup SYNOPSIS
snnewgroup newsgroup [server] [port] DESCRIPTION
snnewgroup creates newsgroup assigning it an upstream NNTP server of server:port. If port is not specified, defaults to 119. If server is also not specified, newsgroup is created as a local group which is fed only by articles POSTed to it. You will need to be root or own /var/spool/sn in order to add new groups. ENVIRONMENT VARIABLES
SNROOT If this is set and is not empty, the value is used in place of /var/spool/sn, the default news spool directory. FILES CREATED
/var/spool/sn/newsgroup Directory where articles will be stored. /var/spool/sn/newsgroup/.created Empty file for the newsgroup creation time. /var/spool/sn/newsgroup/.serial Where snget gets its idea of the new starting serial number for newsgroup on server server:port. The value is initialized to 0. /var/spool/sn/newsgroup/.outgoing If server is specified, is a symlink to /var/spool/sn/.outgoing/server:port, which is a directory, created if it does not already exist. If server is not specified, no file /var/spool/sn/newsgroup/.outgoing will be created. See also snsend. SEE ALSO
sndelgroup, snsend N.B. Harold Tay snnewgroup.v0.3.8(8)