Some days ago, we bought a new two port serial board, and the server assign this new ports as tty02 and tty03, and leaves tty00 and tty01 as unavailable.
I am not sure what you mean by "unavailable": every device in AIX is basically in one of two states (if present at all): do a lsdev -C and you should see a list of devices some of which are in state "Defined" and some are in "Available".
"Defined" menas the definition is there but the device is not usable. "Available" means the device is working. "working" in this case means not only it is (electrically) connected but also that the correct drivers are installed and running. If in doubt, post the output of the commands:
Hai there,
Can any one provide me with a ansi c source code for
opening com1 or com2 and read data. The port is connected to
another serial communication device on rs232 port.
The o/s is Sco Unix 5.0.6
Matter urgent
Viswanath (0 Replies)
hi
i am using solaris 9 on sparc .
i was wondering if there was a command to control my serial interface , as to send a signal periodically every interval of time to the input of a 555 timer .
thanks for your help .... (0 Replies)
Hi,
I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port.
When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Hello!
Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements:
1. Serial port is opened in non-canonical mode.
2. All the time I need to check is there something to read.
3. If I have to write something I need to write it... (6 Replies)
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
HI,
Does anyone installed a GPS from his Serial port to an IBM Server serial port with AIX 5.X
I would like the rs232 configuration you used on the GPS, and the ttys configuration from your server.
Thanks in advance !!! (8 Replies)
Discussion started by: trevian3969
8 Replies
LEARN ABOUT MOJAVE
nsd-xfer
nsd-xfer(8) nsd 3.2.12 nsd-xfer(8)NAME
nsd-xfer - AXFR client to transfer zones from a name server
SYNOPSIS
nsd-xfer [-4] [-6] [-a address[@port]] [-p port] [-s serial] [-T tsiginfo] [-v] -z zone -f file servers
DESCRIPTION
Nsd-xfer is program to transfer zones from a name server using AXFR. NSD is a complete implementation of an authoritative DNS nameserver.
OPTIONS -4 Only send to IPv4 addresses.
-6 Only send to IPv6 addresses.
-a address[@port]
Specify the source address (and port) to send from.
-f file
The file to store the zone in.
-p port
Specify the port to send to.
-s serial
Specify the serial of the current zone. The zone is only transferred if the master server has a zone with a greater serial number.
-T tsiginfo
Use TSIG to verify the zone transfer. The tsiginfo file must contain the TSIG key information. The file is removed upon successful
reading of the key. The format of the tsiginfo file is described in the doc/README file (section 3.3).
-v Be more verbose.
-z zone
Specify the zone to receive.
servers
List of nameservers to try.
EXAMPLES
To run this program the standard way type:
# nsd-xfer -z foobar.cz -f foobar.cz.zone 1.2.3.4
SEE ALSO nsd(8), nsdc(8), nsd.conf(5), nsd-checkconf(8), nsd-notify(8), nsd-patch(8), zonec(8)AUTHORS
NSD was written by NLnet Labs and RIPE NCC joint team. Please see CREDITS file in the distribution for further details.
NLnet Labs jul 19, 2012 nsd-xfer(8)