05-31-2017
It looks like the disk surface might be damaged within that filesystem on one leg of the mirror. You could try to repair the faulty side of the mirror that with format>analyse but you will need to be very careful about the block range you select for checking.
The vtoc will tell you cyls/blocks where that filesystem sits.
Repairing a Defective Sector (System Administration Guide: Devices and File Systems)
When sectors (blocks) are repaired they are often re-vectored within the drive using sectors reserved by the manufacturer for this purpose.
Last edited by hicksd8; 05-31-2017 at 02:36 PM..
10 More Discussions You Might Find Interesting
1. Solaris
I am getting the below mentioned error while trying to unistall a package from a 2.8 Solaris box. Please help..
pkgrm: ERROR: unable to determine current run-state
Removal of <PDMgr> failed (internal error).
No changes were made to the system. (1 Reply)
Discussion started by: chrisanto_2000
1 Replies
2. Filesystems, Disks and Memory
Hi,
I'm attempting to build a raid Z NAS using solaris, but I only have 4 sata ports on my MB, so I bought a Rosewill RC-211 PCIe controller (adds 2 sata II ports).
I'm new to solaris, but I understand that to add a new drive, you first run #devfsadm, which puts the files into /dev/dsk. I... (3 Replies)
Discussion started by: ciscocbee
3 Replies
3. Infrastructure Monitoring
hi folks, i have a snag, when i attempt shutdown of solaris 10 on a sunfire v240 it seems to pause for ages, and goes no further, im busy learning my way around the system so please be patient.
/etc(R)-bash-3.00$ init 6
/etc(R)-bash-3.00$ svc.startd: The system is coming down. Please wait.... (7 Replies)
Discussion started by: alienkidmj12
7 Replies
4. Solaris
Hi,
I am unable to login into my terminal hosting Solaris 10 and get the below error message
"Server refused to allocate pty
ld.so.1: sh: fatal: libc.so.1: open failed: No such file or directory "
Is there anyways i can get into my machine and what kind of changes are required to be... (7 Replies)
Discussion started by: sankasu
7 Replies
5. Solaris
hi friends, i had this problem in a Solaris 10 server
when i inserted my thumbdrive, i can't find the device file containing usb.
what should i do ? (2 Replies)
Discussion started by: Exposure
2 Replies
6. Solaris
I have inherited a solaris 10 server. I went to log into it the other day over the console connection, and after sucessfully entering the password, I was booted back to the login prompt with no errors visible.
If I enter an incorect password, the console displays 'incorrect password' and kicks... (8 Replies)
Discussion started by: Sol-nova
8 Replies
7. Solaris
Hi,
All of our servers run Solaris (currently 10, but looking to upgrade to 11). In each of our offices we have a server configured as a Primary Domain Controller via Samba to provide naming services to our Windoze users. I would like to continue with that arrangement, but I would also like... (2 Replies)
Discussion started by: wgkorb
2 Replies
8. Solaris
HI
I am unable to add printer in solaris (architecture is SUN and OS is Solaris 10) as I try to print the file it gives following error
Failed to contact service for erp-cljCP2025: not-found
Need help
Regards (7 Replies)
Discussion started by: smazshah
7 Replies
9. Solaris
Hi,
we have a sun sparc solaris 10 machine and recently there was a power failure and one of the server domain was down. So today morning i have powered up the domain and it returned me to ok prompt then i have booted the machine with disk from devalias, the system was up as normal and no error... (0 Replies)
Discussion started by: phanidhar6039
0 Replies
10. Solaris
Hello, I followed these instructions to create a Solaris 11 zone:
http://www.oracle.com/technetwork/articles/servers-storage-admin/o11-092-s11-zones-intro-524494.html
And I am unable to ping anything from the Local Zone except for the IP address of the global zone.
My global zone has an IP... (6 Replies)
Discussion started by: unblockable
6 Replies
LEARN ABOUT CENTOS
isosize
ISOSIZE(8) System Administration ISOSIZE(8)
NAME
isosize - output the length of an iso9660 filesystem
SYNOPSIS
isosize [options] iso9660_image_file
DESCRIPTION
This command outputs the length of an iso9660 filesystem that is contained in the specified file. This file may be a normal file or a
block device (e.g. /dev/hdd or /dev/sr0). In the absence of any options (and errors), it will output the size of the iso9660 filesystem in
bytes. This can now be a large number (>> 4 GB).
OPTIONS
-x, --sectors
Show the block count and block size in human-readable form. The output uses the term "sectors" for "blocks".
-d, --divisor number
Only has an effect when -x is not given. The value shown (if no errors) is the iso9660 file size in bytes divided by number. So if
number is the block size then the shown value will be the block count.
The size of the file (or block device) holding an iso9660 filesystem can be marginally larger than the actual size of the iso9660 filesys-
tem. One reason for this is that cd writers are allowed to add "run out" sectors at the end of an iso9660 image.
AVAILABILITY
The isosize command is part of the util-linux package and is available from Linux Kernel Archive <ftp://ftp.kernel.org/pub/linux/utils
/util-linux/>.
util-linux June 2011 ISOSIZE(8)