I have a script that I am having a little trouble with and I hope someone can help.
I will post the code for your input, but I want to read the lines of a file and use this as input to a command in a while loop...
Say my ZONES file produces
Server1
Server2
Server3
then my while loop just now produces:
"this works for Server1"
"this works for Server2" ... etc
but I am wanting to do a zlogin to the server(s) within the global zone to get the crontab info of that server if it has a reboot set.. then i can email it out to the relevant users.
Hi All ,
I try to install some packages in my global zone...
On the execution of the installion of the script it quits by saying the error
"Non global zone check failed"
Kindly help me in this regard
Thanks in advance,
jeganr (7 Replies)
Hi Gurus
I am not able to ping the local zone from global zone
when i am trying to ping i am getting below
ICMP Host Unreachable from gateway zone ( 192.268.35.210)
for icmp from zone ( 192.168.35.210) to sun1 ( 192.168.35.210)
However i can ping local zone from global
please... (12 Replies)
Hi All
There is one folder in global zone I just want to share the same folder innon global zone. How can i do it?
pls send me script for this. (2 Replies)
Dears,
I would like to convert solaris 10 x86 and solaris 10 sparc (Global Zones) physical servers into Local zones.
i found a document which seems to be helpful but i'm stuck @ the 1st step.
to test this i want to do it 1st on x86 system running under vmware ESXi and if it succeeds i will... (1 Reply)
Hi,
We have had a hard drive failure on one of our sandbox OpenSolaris system. We had 2 solaris zones configured at /tank/zones/teamcity and /tank/zones/jira for respective products.
The zpool (tank) was mirrored (2 drives). I'd like to mount the non-faulty drive in the global zone and... (4 Replies)
Hi Greetings...
I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
can some one help me out as it is showing 2 different time zones in global zone and nonglobal zone .In global zone it is showing in GMT while in nonglobal zone i it showing as PDT.
System in running with solaris 10 (3 Replies)
So this is Solaris 11.1. I have a Global zone that has several non-global zones running in it. I want to change the capped-memory.physical resources setting in ALL the zone configs of the running zones.
if I were to do this manually here's what I would do:
zonecfg -z zone1
select... (2 Replies)
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT FREEBSD
crontab
CRONTAB(1) BSD General Commands Manual CRONTAB(1)NAME
crontab -- maintain crontab files for individual users (V3)
SYNOPSIS
crontab [-u user] file
crontab [-u user] { -l | -r | -e }
DESCRIPTION
The crontab utility is the program used to install, deinstall or list the tables used to drive the cron(8) daemon in Vixie Cron. Each user
can have their own crontab, and though these are files in /var, they are not intended to be edited directly.
If the allow file exists, then you must be listed therein in order to be allowed to use this command. If the allow file does not exist but
the deny file does exist, then you must not be listed in the deny file in order to use this command. If neither of these files exists, then
depending on site-dependent configuration parameters, only the super user will be allowed to use this command, or all users will be able to
use this command. The format of these files is one username per line, with no leading or trailing whitespace. Lines of other formats will
be ignored, and so can be used for comments.
The first form of this command is used to install a new crontab from some named file or standard input if the pseudo-filename '-' is given.
The following options are available:
-u Specify the name of the user whose crontab is to be tweaked. If this option is not given, crontab examines ``your'' crontab, i.e.,
the crontab of the person executing the command. Note that su(1) can confuse crontab and that if you are running inside of su(1) you
should always use the -u option for safety's sake.
-l Display the current crontab on standard output.
-r Remove the current crontab.
-e Edit the current crontab using the editor specified by the VISUAL or EDITOR environment variables. The specified editor must edit
the file in place; any editor that unlinks the file and recreates it cannot be used. After you exit from the editor, the modified
crontab will be installed automatically.
FILES
/var/cron/allow List of users allowed to use crontab
/var/cron/deny List of users prohibited from using crontab
/var/cron/tabs Directory for personal crontab files
DIAGNOSTICS
A fairly informative usage message appears if you run it with a bad command line.
SEE ALSO crontab(5), cron(8)STANDARDS
The crontab command conforms to IEEE Std 1003.2 (``POSIX.2'') with the exception that the dangerous variant of calling crontab without a file
name in the first form of the command is not allowed by this implementation. The pseudo-filename '-' must be specified to read from standard
input. The new command syntax differs from previous versions of Vixie Cron, as well as from the classic SVR3 syntax.
AUTHORS
Paul Vixie <paul@vix.com>
BSD May 13, 2010 BSD