05-16-2017
Could this be a routing thing? i.e. there is no route out for 192.168.1.0/24
Can you show us the output from netstat -rn?
Perhaps a trace to check that you are actually connecting to the correct 192.168.1.82. It is possible that you are being routed off elsewhere when you try to connect in. What does traceroute 192.168.1.82 give you from the client end? - or tracert 192.168.1.82 on Windows. Is it what you expect and is it similar to trying to get to the other addresses? Perhaps you are being sent elsewhere and it is rightly rejecting your login attempt. You might need to look at ARP tables to make sure you are getting to the right card by checking the MAC address.
Sorry I can't give more help at the moment,
Robin
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have been looking for info on how to aggregate 2 ore 3 NIC's into into one big pipe. Any advice would be appreciated.
-Chuck (4 Replies)
Discussion started by: 98_1LE
4 Replies
2. UNIX for Dummies Questions & Answers
I did a netstat -an and saw that ntp was listening on 4 UDP ports for each interface. Is this insecure because they are UDP ports and I don't see them in a listen state, is that because they are just a client.
Thank you.
*.ntp Idle... (2 Replies)
Discussion started by: csross
2 Replies
3. UNIX for Dummies Questions & Answers
Greetings!
I just managed to install Solaris 10 on a Sparc based machine. However, there might be a problem with the way ssh is configured.
I CAN ssh from the machine into another on the network (same subnet, as root), but then the newly installed machine CANNOT seem to accept incoming ssh... (2 Replies)
Discussion started by: agummad
2 Replies
4. Shell Programming and Scripting
Hi!
I have two solaris 10 machines(say 10.1.1.1,10.1.1.2). i have installed rsync on 10.1.1.2,
10.1.1.1:::
Sun Microsystems Inc. SunOS 5.10 Generic January 2005
-bash-3.00$ ssh 10.1.1.2 "echo $PATH"
Password:... (4 Replies)
Discussion started by: dddkiran
4 Replies
5. Solaris
Hi,
I am unable to login into my terminal hosting Solaris 10 and get the below error message
"Server refused to allocate pty
ld.so.1: sh: fatal: libc.so.1: open failed: No such file or directory "
Is there anyways i can get into my machine and what kind of changes are required to be... (7 Replies)
Discussion started by: sankasu
7 Replies
6. Solaris
Got a strange problem.
I have 4 Solaris servers all configured the same, Solaris 10 x86 update 10.
When I try to ssh from one Solaris 10 server to another server ssh hangs.
I have an identical server and when I try this everything works fine.
The weird thing is if I am root on the server... (1 Reply)
Discussion started by: ccj4467
1 Replies
7. Red Hat
I want to SSH to 192.168.1.15 Server from my machine, my ip was 192.168.1.99
Source Destination was UP, with IP 192.168.1.15.
This is LAN Network there are 30 Machine's Connected to the network and working fine, I'm Playing around the local machine's because I need to apply the same rules in... (2 Replies)
Discussion started by: babinlonston
2 Replies
8. Red Hat
Dear Concern,
I want to block all ports of a particular node (ip: 172.16.10.141) through iptables. My nodes ip addresses are as below:172.16.10.137
172.16.10.138
Please advise us. (0 Replies)
Discussion started by: makauser
0 Replies
9. AIX
Hello Everyone,
Quick question, any short and fast way to locate and map the physical Ethernet ports on the physical server ?
Server with expansion box has around 12 ethernet ports (fibre and ethernet)
what is the quickest way to map or find out en0 represents which physical port ?
... (1 Reply)
Discussion started by: filosophizer
1 Replies
10. UNIX for Beginners Questions & Answers
Hi folks,
I am fairly a beginner when it comes to Solaris OS administration, but part of my job somehow has scope to provide L1-level of OS administration over a few solaris servers.
Now, we have a requirement to limit the number of simultaneous ssh logins/sessions to the server, sort of... (0 Replies)
Discussion started by: engrcha
0 Replies
LEARN ABOUT DEBIAN
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)
NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <stgt@vger.kernel.org>
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)