04-15-2017
Quote:
Originally Posted by
MadeInGermany
Perhaps the c1 got hung because of a non-responding disk?
Then a reboot might help.
Thanks for the reply.
I tried even rebooting but dint help. Still same issue.
If you check iostat there are so many hardware errors are recorded on all the disks connected with C1.
Any way to confirm if its a faulty controller that is causing the issue?
10 More Discussions You Might Find Interesting
1. Solaris
I am getting the below mentioned error while trying to unistall a package from a 2.8 Solaris box. Please help..
pkgrm: ERROR: unable to determine current run-state
Removal of <PDMgr> failed (internal error).
No changes were made to the system. (1 Reply)
Discussion started by: chrisanto_2000
1 Replies
2. Filesystems, Disks and Memory
Hi,
I'm attempting to build a raid Z NAS using solaris, but I only have 4 sata ports on my MB, so I bought a Rosewill RC-211 PCIe controller (adds 2 sata II ports).
I'm new to solaris, but I understand that to add a new drive, you first run #devfsadm, which puts the files into /dev/dsk. I... (3 Replies)
Discussion started by: ciscocbee
3 Replies
3. Infrastructure Monitoring
hi folks, i have a snag, when i attempt shutdown of solaris 10 on a sunfire v240 it seems to pause for ages, and goes no further, im busy learning my way around the system so please be patient.
/etc(R)-bash-3.00$ init 6
/etc(R)-bash-3.00$ svc.startd: The system is coming down. Please wait.... (7 Replies)
Discussion started by: alienkidmj12
7 Replies
4. Solaris
Hi,
I am unable to login into my terminal hosting Solaris 10 and get the below error message
"Server refused to allocate pty
ld.so.1: sh: fatal: libc.so.1: open failed: No such file or directory "
Is there anyways i can get into my machine and what kind of changes are required to be... (7 Replies)
Discussion started by: sankasu
7 Replies
5. Solaris
hi friends, i had this problem in a Solaris 10 server
when i inserted my thumbdrive, i can't find the device file containing usb.
what should i do ? (2 Replies)
Discussion started by: Exposure
2 Replies
6. Solaris
I have inherited a solaris 10 server. I went to log into it the other day over the console connection, and after sucessfully entering the password, I was booted back to the login prompt with no errors visible.
If I enter an incorect password, the console displays 'incorrect password' and kicks... (8 Replies)
Discussion started by: Sol-nova
8 Replies
7. Solaris
Hi,
All of our servers run Solaris (currently 10, but looking to upgrade to 11). In each of our offices we have a server configured as a Primary Domain Controller via Samba to provide naming services to our Windoze users. I would like to continue with that arrangement, but I would also like... (2 Replies)
Discussion started by: wgkorb
2 Replies
8. Solaris
HI
I am unable to add printer in solaris (architecture is SUN and OS is Solaris 10) as I try to print the file it gives following error
Failed to contact service for erp-cljCP2025: not-found
Need help
Regards (7 Replies)
Discussion started by: smazshah
7 Replies
9. Solaris
Hi,
we have a sun sparc solaris 10 machine and recently there was a power failure and one of the server domain was down. So today morning i have powered up the domain and it returned me to ok prompt then i have booted the machine with disk from devalias, the system was up as normal and no error... (0 Replies)
Discussion started by: phanidhar6039
0 Replies
10. Solaris
Hello, I followed these instructions to create a Solaris 11 zone:
http://www.oracle.com/technetwork/articles/servers-storage-admin/o11-092-s11-zones-intro-524494.html
And I am unable to ping anything from the Local Zone except for the IP address of the global zone.
My global zone has an IP... (6 Replies)
Discussion started by: unblockable
6 Replies
LEARN ABOUT ULTRIX
iostat
iostat(1) General Commands Manual iostat(1)
Name
iostat - report I/O statistics
Syntax
iostat [ -c ] [ -t ] [ disknames ] [ interval ] [ count ]
Description
The command reports I/O statistics for terminals, disks and cpus. For terminals the number of input and output characters are counted.
For disks the number of 512 byte blocks per second and number of transfers per second are displayed. For cpus, it provides the percentage
of time the system has spent in user mode, in user mode running low priority (niced) processes, in system mode, and idling. On multipro-
cessor systems these cpu statistics represent a cumulative summary of all the cpus.
The optional disknames argument causes disk statistics to be displayed for the specified disks. If this argument is not specified then
disk statistics will be displayed for the first 3 disks only.
The optional interval argument causes to report once each interval seconds. The first report is for all time since a reboot and each sub-
sequent report is for the last interval only.
The optional count argument restricts the number of reports.
Options
-c Displays the percentage of time each cpu spent in user mode, running low priority (nice'd) processes, in system mode, and idling.
-t Displays the number of characters read from and written to terminals.
Examples
This example will cause cpu and disk statistics for the 5 disks ra0, ra1, ra2, ra3, and ra4.
iostat ra0 ra1 ra2 ra3 ra4
This example will cause cpu, terminal, and disk statistics for ra0 to be displayed and updated every 2 seconds.
iostat -t ra0 2
Files
See Also
vmstat(1), cpustat(1)
iostat(1)