03-09-2017
Is the VPN something you control? You're using it in bridging mode, which takes over your connection, but if you use routing mode, it doesn't... Routing mode just allows you to connect to a new subnet of IP's.
10 More Discussions You Might Find Interesting
1. Cybersecurity
Hello,
I am currently trying to limit incoming UDP length 20 packets on a per IP basis to 5 a second using IPTables on a Linux machine (CentOS 5.2).
Basically, if an IP is sending more than 5 length 20 UDP packet a second to the local machine, I would like the machine to drop the excess... (1 Reply)
Discussion started by: tomboy123
1 Replies
2. Solaris
Hi All,
yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'.
I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies
3. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
4. UNIX for Dummies Questions & Answers
Hi all,
I am new to Linux kernel.
we have a c file that counts the no. of sends and received packets in each interface, and indicate the user about the error/drop ration of incoming and outgoing packets.
in our Linux box , the incoming packets are dropped at random interval.
we have our... (1 Reply)
Discussion started by: kannandv
1 Replies
5. Solaris
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies
6. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
7. IP Networking
hello,
can anyone suggest how to delay the incoming packets ??
or how the packets are prossed inside the kernal and a way to make the packets wait a while??
it wud be vry helpful
regards
sameer (7 Replies)
Discussion started by: sameer kulkarni
7 Replies
8. Linux
I am looking for an iptables command to allow incoming UDP packets for my Linux server
also is there a command I can use to set the default action for outgoing packets to accept?
Thank you (1 Reply)
Discussion started by: crimputt
1 Replies
9. IP Networking
Hi,
I'm quite new to unix networking and ip tables. I'm running a debian (htpc) server with two NIC's; eth0 and wlan0.
I'm trying to set it up in a way that eth0 is the default interface for internet, but some processes should run through wlan0.
For example, I'm using eth0 for downloads... (2 Replies)
Discussion started by: Subbeh
2 Replies
10. IP Networking
Hello, I'm trying to route all packets arriving at a particular interface by entering the same interface
the virtual interface eth1: 2 and now everything is routed by default gw configured on eth1.
eth1 Link encap:Ethernet HWaddr 0a:0e:64:18:52:72
inet addr:192.168.10.15
eth1:2 ... (1 Reply)
Discussion started by: faka
1 Replies