SHOREWALL-TUNNELS(5)						  [FIXME: manual]					      SHOREWALL-TUNNELS(5)

NAME

       tunnels - Shorewall VPN definition file

SYNOPSIS

       /etc/shorewall/tunnels

DESCRIPTION

       The tunnels file is used to define rules for encapsulated (usually encrypted) traffic to pass between the Shorewall system and a remote
       gateway. Traffic flowing through the tunnel is handled using the normal zone/policy/rule mechanism. See
       http://www.shorewall.net/VPNBasics.html for details.

       The columns in the file are as follows.

       TYPE -
       {ipsec[:{noah|ah}]|ipsecnat|ipip|gre|l2tp|pptpclient|pptpserver|COMMENT|{openvpn|openvpnclient|openvpnserver}[:{tcp|udp}][:port]|generic:protocol[:port]}
	   Types are as follows:

		       6to4 or 6in4  - 6to4 or 6in4 tunnel. The 6in4 synonym was added in 4.4.24.
		       ipsec	     - IPv4 IPSEC
		       ipsecnat      - IPv4 IPSEC with NAT Traversal (UDP port 4500 encapsulation)
		       ipip	     - IPv4 encapsulated in IPv4 (Protocol 4)
		       gre	     - Generalized Routing Encapsulation (Protocol 47)
		       l2tp	     - Layer 2 Tunneling Protocol (UDP port 1701)
		       pptpclient    - PPTP Client runs on the firewall
		       pptpserver    - PPTP Server runs on the firewall
		       openvpn	     - OpenVPN in point-to-point mode
		       openvpnclient - OpenVPN client runs on the firewall
		       openvpnserver - OpenVPN server runs on the firewall
		       generic	     - Other tunnel type

	   If the type is ipsec, it may be followed by :ah to indicate that the Authentication Headers protocol (51) is used by the tunnel (the
	   default is :noah which means that protocol 51 is not used). NAT traversal is only supported with ESP (protocol 50) so ipsecnat tunnels
	   don't allow the ah option (ipsecnat:noah may be specified but is redundant).

	   If type is openvpn, openvpnclient or openvpnserver it may optionally be followed by ":" and tcp or udp to specify the protocol to be
	   used. If not specified, udp is assumed.

	   If type is openvpn, openvpnclient or openvpnserver it may optionally be followed by ":" and the port number used by the tunnel. if no
	   ":" and port number are included, then the default port of 1194 will be used. . Where both the protocol and port are specified, the
	   protocol must be given first (e.g., openvpn:tcp:4444).

	   If type is generic, it must be followed by ":" and a protocol name (from /etc/protocols) or a protocol number. If the protocol is tcp
	   or udp (6 or 17), then it may optionally be followed by ":" and a port number.

	   Comments may be attached to Netfilter rules generated from entries in this file through the use of COMMENT lines. These lines begin
	   with the word COMMENT; the remainder of the line is treated as a comment which is attached to subsequent rules until another COMMENT
	   line is found or until the end of the file is reached. To stop adding comments to rules, use a line with only the word COMMENT.

       ZONE - zone
	   The zone of the physical interface through which tunnel traffic passes. This is normally your internet zone.

       GATEWAY(S) (gateway or gateways) - address-or-range [ , ... ]
	   The IP address of the remote tunnel gateway. If the remote gateway has no fixed address (Road Warrior) then specify the gateway as
	   0.0.0.0/0. May be specified as a network address and if your kernel and iptables include iprange match support then IP address ranges
	   are also allowed.

	   Beginning with Shorewall 4.5.3, a list of addresses or ranges may be given. Exclusion (shorewall-exclusion[1] (5) ) is not supported.

       GATEWAY ZONES (gateway_zone or gateway_zones) - [zone[,zone]...]
	   Optional. If the gateway system specified in the third column is a standalone host then this column should contain a comma-separated
	   list of the names of the zones that the host might be in. This column only applies to IPSEC tunnels where it enables ISAKMP traffic to
	   flow through the tunnel to the remote gateway(s).

EXAMPLE

       Example 1:
	   IPSec tunnel.

	   The remote gateway is 4.33.99.124 and the remote subnet is 192.168.9.0/24. The tunnel does not use the AH protocol

		       #TYPE	       ZONE    GATEWAY
		       ipsec:noah      net     4.33.99.124

       Example 2:
	   Road Warrior (LapTop that may connect from anywhere) where the "gw" zone is used to represent the remote LapTop

		       #TYPE	       ZONE    GATEWAY	       GATEWAY ZONES
		       ipsec	       net     0.0.0.0/0       gw

       Example 3:
	   Host 4.33.99.124 is a standalone system connected via an ipsec tunnel to the firewall system. The host is in zone gw.

		       #TYPE	       ZONE    GATEWAY	       GATEWAY ZONES
		       ipsec	       net     4.33.99.124     gw

       Example 4:
	   Road Warriors that may belong to zones vpn1, vpn2 or vpn3. The FreeS/Wan _updown script will add the host to the appropriate zone using
	   the shorewall add command on connect and will remove the host from the zone at disconnect time.

		       #TYPE	       ZONE    GATEWAY	       GATEWAY ZONES
		       ipsec	       net     0.0.0.0/0       vpn1,vpn2,vpn3

       Example 5:
	   You run the Linux PPTP client on your firewall and connect to server 192.0.2.221.

		       #TYPE	       ZONE    GATEWAY	       GATEWAY ZONES
		       pptpclient      net     192.0.2.221

       Example 6:
	   You run a PPTP server on your firewall.

		       #TYPE	       ZONE    GATEWAY	       GATEWAY ZONES
		       pptpserver      net     0.0.0.0/0

       Example 7:
	   OPENVPN tunnel. The remote gateway is 4.33.99.124 and openvpn uses port 7777.

		       #TYPE	       ZONE    GATEWAY	       GATEWAY ZONES
		       openvpn:7777    net     4.33.99.124

       Example 8:
	   You have a tunnel that is not one of the supported types. Your tunnel uses UDP port 4444. The other end of the tunnel is 4.3.99.124.

		       #TYPE		ZONE	GATEWAY 	GATEWAY ZONES
		       generic:udp:4444 net	4.3.99.124

FILES

       /etc/shorewall/tunnels

SEE ALSO

       http://shorewall.net/configuration_file_basics.htm#Pairs

       shorewall(8), shorewall-accounting(5), shorewall-actions(5), shorewall-blacklist(5), shorewall-hosts(5), shorewall_interfaces(5),
       shorewall-ipsets(5), shorewall-maclist(5), shorewall-masq(5), shorewall-nat(5), shorewall-netmap(5), shorewall-params(5),
       shorewall-policy(5), shorewall-providers(5), shorewall-proxyarp(5), shorewall-rtrules(5), shorewall-routestopped(5), shorewall-rules(5),
       shorewall.conf(5), shorewall-secmarks(5), shorewall-tcclasses(5), shorewall-tcdevices(5), shorewall-tcrules(5), shorewall-tos(5),
       shorewall-zones(5)

NOTES

	1. shorewall-exclusion
	   http://www.shorewall.net/manpages/shorewall-exclusion.html

[FIXME: source] 						    06/28/2012						      SHOREWALL-TUNNELS(5)