03-09-2017
I don't quite get what you are trying to do. Maybe you want TAP - bridge from eth1: to eth0: Which you not have now. In other words segregate and bridge on this server. Is this box in the DMZ?
10 More Discussions You Might Find Interesting
1. Cybersecurity
Hello,
I am currently trying to limit incoming UDP length 20 packets on a per IP basis to 5 a second using IPTables on a Linux machine (CentOS 5.2).
Basically, if an IP is sending more than 5 length 20 UDP packet a second to the local machine, I would like the machine to drop the excess... (1 Reply)
Discussion started by: tomboy123
1 Replies
2. Solaris
Hi All,
yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'.
I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies
3. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
4. UNIX for Dummies Questions & Answers
Hi all,
I am new to Linux kernel.
we have a c file that counts the no. of sends and received packets in each interface, and indicate the user about the error/drop ration of incoming and outgoing packets.
in our Linux box , the incoming packets are dropped at random interval.
we have our... (1 Reply)
Discussion started by: kannandv
1 Replies
5. Solaris
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies
6. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
7. IP Networking
hello,
can anyone suggest how to delay the incoming packets ??
or how the packets are prossed inside the kernal and a way to make the packets wait a while??
it wud be vry helpful
regards
sameer (7 Replies)
Discussion started by: sameer kulkarni
7 Replies
8. Linux
I am looking for an iptables command to allow incoming UDP packets for my Linux server
also is there a command I can use to set the default action for outgoing packets to accept?
Thank you (1 Reply)
Discussion started by: crimputt
1 Replies
9. IP Networking
Hi,
I'm quite new to unix networking and ip tables. I'm running a debian (htpc) server with two NIC's; eth0 and wlan0.
I'm trying to set it up in a way that eth0 is the default interface for internet, but some processes should run through wlan0.
For example, I'm using eth0 for downloads... (2 Replies)
Discussion started by: Subbeh
2 Replies
10. IP Networking
Hello, I'm trying to route all packets arriving at a particular interface by entering the same interface
the virtual interface eth1: 2 and now everything is routed by default gw configured on eth1.
eth1 Link encap:Ethernet HWaddr 0a:0e:64:18:52:72
inet addr:192.168.10.15
eth1:2 ... (1 Reply)
Discussion started by: faka
1 Replies
LEARN ABOUT NETBSD
bridge
BRIDGE(4) BSD Kernel Interfaces Manual BRIDGE(4)
NAME
bridge -- network bridge device
SYNOPSIS
pseudo-device bridge
DESCRIPTION
The bridge driver creates a logical link between two or more IEEE 802 networks that use the same (or ``similar enough'') framing format. For
example, it is possible to bridge Ethernet and 802.11 networks together, but it is not possible to bridge Ethernet and Token Ring together.
To use bridge, the administrator must first create the interface and configure the bridge parameters. The bridge is created using the
ifconfig(8) create subcommand. The learning and forwarding behavior and other parameters of a bridge are configured by the brconfig(8) util-
ity.
A bridge can be used to provide several services, such as a simple 802.11-to-Ethernet bridge for wireless hosts, and traffic isolation.
A bridge works like a switch, forwarding traffic from one interface to another. Multicast and broadcast packets are always forwarded to all
interfaces that are part of the bridge. For unicast traffic, the bridge learns which MAC addresses are associated with which interfaces and
will forward the traffic selectively.
The bridge driver implements the IEEE 802.1D Spanning Tree protocol (STP). Spanning Tree is used to detect and remove loops in a network
topology.
Transparent filtering for IP and IPv6 packets can be added with the kernel configuration option options BRIDGE_IPF.
When filtering is enabled, bridged packets will pass through the filter inbound on the originating interface and outbound on the appropriate
interfaces. ARP and REVARP packets are forwarded without being filtered and others that are not IP nor IPv6 packets are not forwarded when
filtering is enabled.
Note that packets to and from the bridging host will be seen by the filter on the interface with the appropriate address configured as well
as on the interface on which the packet arrives or departs.
SEE ALSO
etherip(4), options(4), brconfig(8), ipf(8)
HISTORY
The bridge driver first appeared in NetBSD 1.6.
AUTHORS
The bridge driver was originally written by Jason L. Wright <jason@thought.net> as part of an undergraduate independent study at the Univer-
sity of North Carolina at Greensboro.
This version of the bridge driver has been heavily modified from the original version by Jason R. Thorpe <thorpej@wasabisystems.com>.
BUGS
The bridge driver currently supports only Ethernet and Ethernet-like (e.g. 802.11) network devices, with exactly the same interface MTU size
as the bridge device.
The bridge driver currently does not support snooping via bpf(4).
BSD
January 9, 2010 BSD