Hello,
I need some help in recovering ZFS pool. Here is scenerio. There are two disks -
c0t0d0 - This is good disk. I cloned it from other server and boot server from this disk.
c0t1d0 - This is original disk of this server, having errors. I am able to mount it on /mnt. So that I can copy required data from this to c0t0d0
Below pool is not imported yet and copy of another server, from where I have cloned.
Code:
# zpool import
pool: zplctpool
id: 11623878967666942759
state: DEGRADED
status: The pool was last accessed by another system.
action: The pool can be imported despite missing or damaged devices. The
fault tolerance of the pool may be compromised if imported.
see: http://www.sun.com/msg/ZFS-8000-EY
config:
zplctpool DEGRADED
mirror DEGRADED
c0t0d0s7 FAULTED corrupted data
c0t0d0s7 ONLINE
I do not want this zplctpool, it can be deleted. Instead, I want zplctpool, which is sitting on c0t1d0s7
Regards
assuming this is NOT your /rpool, simply export the existing zpool on the current c0t0d0s7, remove the disk and then with the new disk installed do a
Hi All,
While my LINUX SERVER installed we didnt' used all the space for partitions. with what tool I can create a new partition or mount point to use the free space.
I tried the command fdisk and diskdruid. They are not working.
Thanks in advance
With Best regards,
Varma. (2 Replies)
Have a solaris x86 running solaris 9.
Root disk - logical - mirrored.
I added 2 more disks today - and I have mirrored them using array configuration utility.
I did a reconfiguration boot - and now I can see the logical disk using format:
I then partitioned this the way I wanted (I hope)... (4 Replies)
I have 3 disks to partition in following file system.
c1t1d0 = 72gb
/prod1
/prod2
/prod3
/prod4
/prod5
I am first time using "format" command to do this. How can i name with specified size.
-Adeel (1 Reply)
Hello,
I am a new member of the forum.
I need an idea on how to partition the disk.
My situation is as follows:
I have two 3TB disks ognuno.In 6TB total then, but I have to do to force a RAID 1 so my space will be 3TB. I'll have to force install RedHat 5.8 and liquids is to be taken in... (4 Replies)
Hi,
Quick question.
I have a data zpool that consists of 1 disk.
pool: data
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
data ONLINE 0 0 0
c0t50002AC0014B06BEd0 ONLINE... (2 Replies)
I added a disk to a zpool using "zpool add diskname"
My intention was mirror a zpool disk that no mirror; that is a zpool with only one disk. I did not issue the right command. Now, the disk has been added successfully but I cannot remove nor detach it as Solaris 11 thinks it has data on it... (14 Replies)
issue,
I had a zpool which was full
pool_temp1 199G 197G 1.56G 99% ONLINE -
pool_temp2 199G 196G 3.09G 98% ONLINE -
as you can see, full
so I replaced with a larger disk.
zpool replace pool_temp1 c3t600144F0FF8BA036000058CC1DB80008d0s0... (2 Replies)
Generally, this is what we do:-
On primary, export 2 LUNs (add-vdsdev).
On primary, assign these disks to the ldom in question (add-vdisk).
On ldom, created mirrored zpool from these two disks.
On one server (which is older) we have:-
On primary, create mirrored zpool from the two LUNs.... (4 Replies)
On an OmniOS server, I removed a single-disk pool I was using for testing.
Now, when I run zpool import it will show it as FAULTED, since that single disk not available anymore.
# zpool import
pool: fido
id: 7452075738474086658
state: FAULTED
status: The pool was last... (11 Replies)
Discussion started by: priyadarshan
11 Replies
LEARN ABOUT SUNOS
raidctl
raidctl(1M) System Administration Commands raidctl(1M)NAME
raidctl - RAID hardware utility
SYNOPSIS
raidctl -c disk1 disk2
raidctl -d disk1
raidctl [-f] -F filename controller...
raidctl -l [controller...]
DESCRIPTION
The raidctl utility creates, deletes, or displays RAID volumes of the LSI1030 HW Raid controllers that include RAID support. The utility
also updates firmware/fcode/BIOS for both RAID and non-RAID controllers.
The raidctl utility requires privileges that are controlled by the underlying file-system permissions. Only privileged users can manipulate
the RAID system configuration. If a non-privileged user attempts to create or delete a RAID volume, the command fails with EPERM.
Without options, raidctl displays the current RAID configuration on all exisiting controllers.
OPTIONS
The following options are supported:
-c disk1 disk2 (for on board)
Create a mirror using disk1 and disk2. Replace the contents of disk2 with the contents of disk1. Specify disk1 and disk2 in canonical
form, for example, c0t0d0.
When you create a a RAID volume, the RAID volume assumes the identity of the first target in the disk pair (disk1). The second target
(disk2) disappears from the system. Therefore, the RAID volume appears as one disk.
To have a successful RAID creation, there must not already be a RAID configuration present on the specified controller. Additionally,
the secondary disk must not be mounted, as it has all its data erased and replaced with the primary disk's data.
-d disk1 (for on board)
Delete the RAID volume specified as disk1.
Specify disk1 in canonical form, for example, c0t0d0.
-f (for HBA)
Force an update. Do not prompt.
-F filename controller (for HBA)
Update the firmware running on the specified controller (controller).
-l [controller ...] (for on board)
List the system's RAID configuration. If controller is specified, list RAID configurations for controller.
Output from the -l lists the following information:
RAID Volume Displays logical RAID volume name.
RAID Status Displays RAID status as either RESYNCING (disks are syncing), DEGRADED RAID is operating with reduced functionality),
OK (operating optimally), or FAILED (non-functional).
RAID Disk Displays RAID disk name.
Disk Status Displays disk status as either OK or FAILED.
EXAMPLES
Example 1: Creating the RAID Configuration
The following command creates the RAID configuration:
# raidctl -c c0t0d0 c0t1d0
RAID Volume 'c0t0d0' created
Example 2: Displaying the RAID Configuration
The following command displays the RAID configuration:
# raidctl
RAID RAID RAID Disk
Volume Status Disk Status
----------------------------------------
c0t0d0 RESYNCING c0t0d0 OK
c0t1d0 OK
Example 3: Deleting the RAID Configuration
The following command deletes the RAID configuration:
# raidctl -d c0t0d0
RAID Volume 'c0t0d0' deleted
Example 4: Updating Flash Images on the Controller
The following command updates flash images on the controller:
# raidctl -F lsi1030.fw 0
Update flash image on controller 0? (y/N): y
Flash updated successfully
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 Invalid command line input.
2 Request operation failed.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO attributes(5)
System Administration Guide: Basic Administration
SunOS 5.10 17 Aug 2004 raidctl(1M)