Hello,
I need some help in recovering ZFS pool. Here is scenerio. There are two disks -
c0t0d0 - This is good disk. I cloned it from other server and boot server from this disk.
c0t1d0 - This is original disk of this server, having errors. I am able to mount it on /mnt. So that I can copy required data from this to c0t0d0
Below pool is not imported yet and copy of another server, from where I have cloned.
I do not want this zplctpool, it can be deleted. Instead, I want zplctpool, which is sitting on c0t1d0s7
Regards
assuming this is NOT your /rpool, simply export the existing zpool on the current c0t0d0s7, remove the disk and then with the new disk installed do a
Hi All,
While my LINUX SERVER installed we didnt' used all the space for partitions. with what tool I can create a new partition or mount point to use the free space.
I tried the command fdisk and diskdruid. They are not working.
Thanks in advance
With Best regards,
Varma. (2 Replies)
Have a solaris x86 running solaris 9.
Root disk - logical - mirrored.
I added 2 more disks today - and I have mirrored them using array configuration utility.
I did a reconfiguration boot - and now I can see the logical disk using format:
I then partitioned this the way I wanted (I hope)... (4 Replies)
I have 3 disks to partition in following file system.
c1t1d0 = 72gb
/prod1
/prod2
/prod3
/prod4
/prod5
I am first time using "format" command to do this. How can i name with specified size.
-Adeel (1 Reply)
Hello,
I am a new member of the forum.
I need an idea on how to partition the disk.
My situation is as follows:
I have two 3TB disks ognuno.In 6TB total then, but I have to do to force a RAID 1 so my space will be 3TB. I'll have to force install RedHat 5.8 and liquids is to be taken in... (4 Replies)
Hi,
Quick question.
I have a data zpool that consists of 1 disk.
pool: data
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
data ONLINE 0 0 0
c0t50002AC0014B06BEd0 ONLINE... (2 Replies)
I added a disk to a zpool using "zpool add diskname"
My intention was mirror a zpool disk that no mirror; that is a zpool with only one disk. I did not issue the right command. Now, the disk has been added successfully but I cannot remove nor detach it as Solaris 11 thinks it has data on it... (14 Replies)
issue,
I had a zpool which was full
pool_temp1 199G 197G 1.56G 99% ONLINE -
pool_temp2 199G 196G 3.09G 98% ONLINE -
as you can see, full
so I replaced with a larger disk.
zpool replace pool_temp1 c3t600144F0FF8BA036000058CC1DB80008d0s0... (2 Replies)
Generally, this is what we do:-
On primary, export 2 LUNs (add-vdsdev).
On primary, assign these disks to the ldom in question (add-vdisk).
On ldom, created mirrored zpool from these two disks.
On one server (which is older) we have:-
On primary, create mirrored zpool from the two LUNs.... (4 Replies)
On an OmniOS server, I removed a single-disk pool I was using for testing.
Now, when I run zpool import it will show it as FAULTED, since that single disk not available anymore.
# zpool import
pool: fido
id: 7452075738474086658
state: FAULTED
status: The pool was last... (11 Replies)
Discussion started by: priyadarshan
11 Replies
LEARN ABOUT OPENSOLARIS
zdb
zdb(1M) System Administration Commands zdb(1M)NAME
zdb - ZFS debugger
SYNOPSIS
zdb pool
DESCRIPTION
The zdb command is used by support engineers to diagnose failures and gather statistics. Since the ZFS file system is always consistent on
disk and is self-repairing, zdb should only be run under the direction by a support engineer.
If no arguments are specified, zdb, performs basic consistency checks on the pool and associated datasets, and report any problems
detected.
Any options supported by this command are internal to Sun and subject to change at any time.
EXIT STATUS
The following exit values are returned:
0 The pool is consistent.
1 An error was detected.
2 Invalid command line options were specified.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWzfsu |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable |
+-----------------------------+-----------------------------+
SEE ALSO zfs(1M), zpool(1M), attributes(5)SunOS 5.11 31 Oct 2005 zdb(1M)