M 47 HIS:LOT 32 DUTY 2 MIKE, FINISHED
MIKE ACTIVE STATUS
23TASK YES GOOD
100TASK NO GOOD
========================================
M 47 HIS:LOT 1 DUTY 1 MIKE, FINISHED
MIKE ACTIVE STATUS
23TASK YES GOOD
... (7 Replies)
Hello all,
I have a test file that has the format:
.....
O
3.694950 -.895050 1.480000
O
5.485050 .895050 1.480000
Ti
-4.590000 4.590000 2.960000
Ti
-2.295000 ... (5 Replies)
I'm looking for a sort command that will sort by zip code first then by last name. (zip code is the last field, last name is first field)
data file looks like this.
Hope Bob 1234 Main ST. Colorado Springs, CO 80920
I was thinking along the lines of:
sort -k9n address.data //for the... (2 Replies)
I was trying to check for the sort of some columns (say 1-10) of particular file. Now, by default, the Unix sort uses as a separator whitespace (e.g. if you have 'foo bar' then it separates it into 'foo' and 'bar' to use as keys)
Now, I know which particular columns I want to use as the sort... (1 Reply)
Hi all.
Is there a way that I can use the sort command too sort the following field by earliest time (12:00AM) to latest time (11:59PM)?
07:12PM
07:53PM
07:54PM
08:07PM
10:15AM
10:21AM
TIA!!!!!! (1 Reply)
Hello,
I have a large data file:
1234 8888 bbb
2745 8888 bbb
9489 8888 bbb
1234 8888 aaa
4838 8888 aaa
3977 8888 aaa
I need to remove duplicate lines (where the first column is the duplicate). I have been using:
sort file.txt | uniq -w4 > newfile.txt
However, it seems to keep the... (11 Replies)
Hi Guys,
I have a file to be sorted and uniq with the following format.
S00001002|01|20021231
S00001002|01|20011031
S00001006|01|20120430
S00001006|01|20111231
S00001006|01|20111031
S00001006|01|20110831
S00001006|01|20110731
S00001006|01|20101231
S00001006|01|20091231... (5 Replies)
I have a file like this:
/vol/eng_app_0103z
/vol/eng_app_0103z
/vol/eng_app_0120z
/vol/eng_app_0126z
/vol/eng_app_0144z
/vol/eng_app_0150z
/vol/eng_app_0154z
/vol/eng_app_01551z
/vol/eng_app_01552z
/vol/eng_app_0155z
/vol/eng_app_0164z
/vol/eng_app_0199zWhen I use the sort command... (3 Replies)
I have a question about what the sort command is doing.
Here is some sample data:
348201310013RVE 2
600201310013GFJ 70
3302013020101NS 40
600201309013GFJ 70
The sort command that is running is as follows:
sort -k 1,3 -k 12,4 input.txt > output.txt
... (6 Replies)
Discussion started by: Drenhead
6 Replies
LEARN ABOUT NETBSD
agr
AGR(4) BSD Kernel Interfaces Manual AGR(4)NAME
agr -- link aggregation pseudo network interface driver
SYNOPSIS
pseudo-device agr
DESCRIPTION
The agr driver provides link aggregation functionality (a.k.a. L2 trunking or bonding).
It supports the IEEE 802.3ad Link Aggregation Control Protocol (LACP) and the Marker Protocol.
The agr driver supports the following link specific flags for ifconfig(8):
link0 Use the round-robin distribution algorithm. Don't use it unless you're really sure, because it violates the frame ordering rule.
-link0 Use the default distribution algorithm, which is based on the hash of DA/SA, TCI, and, if available, some upper layer protocol infor-
mation like ip(4) DA/SA.
link1 Disable LACP. Prevents any LACP or Marker messaging which leaves the ports in the default static configuration. Set this prior to
adding ports.
EXAMPLES
Create an agr interface, agr0, and attach re0 and re1 to it. In other words, aggregate re0 and re1 so that they can be used as a single
interface, agr0. The physical interfaces which are attached to the agr interface must not have any IP addresses, neither IPv4 nor IPv6.
ifconfig re0 inet xxx.xxx.xxx.xxx delete
ifconfig re0 inet6 fe80::xxxx:xxxx:xxxx:xxxx delete
ifconfig re1 inet xxx.xxx.xxx.xxx delete
ifconfig re1 inet6 fe80::xxxx:xxxx:xxxx:xxxx delete
ifconfig agr0 create
ifconfig agr0 agrport re0
ifconfig agr0 agrport re1
Destroy an interface created in the above example.
ifconfig agr0 -agrport re0
ifconfig agr0 -agrport re1
ifconfig agr0 destroy
SEE ALSO ifconfig(8)STANDARDS
IEEE 802.3ad Aggregation of Multiple Link Segments
HISTORY
The agr driver first appeared in NetBSD 4.0.
AUTHORS
The agr driver was written by YAMAMOTO Takashi.
BUGS
There is no way to configure LACP administrative variables, including system and port priorities. The current implementation of the agr
driver always performs active-mode LACP and uses 0x8000 as system and port priorities.
The agr driver uses the MAC address of the first-added physical interface as the MAC address of the agr interface itself. Thus, removing the
physical interface and using it for another purpose can result in non-unique MAC addresses.
The current implementation of the agr driver doesn't prevent unsafe operations like some ioctls against underlying physical interfaces. Such
operations can result in unexpected behaviors, and are strongly discouraged.
There is no way to configure agr interfaces without attaching physical interfaces.
Physical interfaces being added to the agr interface shouldn't have any addresses except for link level address. Otherwise, the attempt will
fail with EBUSY. Note that it includes an automatically assigned IPv6 link-local address.
BSD February 23, 2010 BSD