|
|
Sponsored Content
Top Forums
UNIX for Advanced & Expert Users
Unable to ping default gateway
Post 302992674 by RudiC on Tuesday 28th of February 2017 12:47:51 PM
02-28-2017
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
3. Solaris
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies
4. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
5. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
6. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
7. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
8. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
9. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT ULTRIX
lamnodes
LAMNODES(1) LAM TOOLS LAMNODES(1) NAME
lamnodes - Resolve LAM node/CPU notation to Unix hostnames. SYNOPSIS
lamnodes [-chin] [where] OPTIONS
-c Suppress printing the CPU count for each node. -h Print the command help menu. -i Print IP addresses (instead of IP names) -n Suppress printing CPU count for each node DESCRIPTION
The lamnodes command is used to resolve LAM node/CPU nomenclature to Unix hostnames. It can be used to determine the current running con- figuration of the LAM/MPI run-time environment, and generate a boot schema that can be used to launch LAM in the future. By default, lamnodes will print out the node number, default IP name, CPU count, and per-node flags for each node in the running LAM. gethostbyaddr(3) is used to obtain default hostnames. If gethostbyaddr(3) fails, the IP number is displayed instead. This command can be used by setup shell scripts (and the like) to determine information from a currently-running LAM universe. For exam- ple, use lamnodes to resolve particular CPUs and/or nodes to specific unix hostnames. In a batch environment, lamnodes can be used to determine which CPUs share a common node (note that MPI_GET_PROCESSOR_NAME can be used for a similar effect in an MPI program). lamnodes also shows per-node flags. Currently defined flags are: origin The node where lamboot was executed. this_node The node where lamnodes is running. no_schedule The node will not be used to run MPI and serial processes when N and C are used to mpirun and lamexec. EXAMPLES
lamnodes N -n Display IP names and CPU counts for all nodes. This output can be saved and later used with lamboot(1). lamnodes C -n -c Display the IP name of the nodes containing each CPU, and suppress the LAM node number and CPU count. This output can be saved and later used with lamboot(1). SEE ALSO
bhost(5), gethostbyaddr(3), lamboot(1) LAM 7.1.4 July, 2007 LAMNODES(1)