I'm trying to insert multiple new lines of text into an iptables script using sed in a while loop. I'm not sure if this is the most effective way. Searching the forums has helped me come up with a good beginning but it's not 100%. I'd like it to search out a unique line in my current iptables file... (2 Replies)
Hi
I have small home network and I want to block some forums on web
When I use this
iptables -A INPUT -s forum -j DROP
rules is applied but when I restart some of PC rules are not present any more also I tried to save firewall settings
iptables-save > /root/dsl.fw
but how to... (2 Replies)
Hello,
I was playing around with iptables to setup an isolated system. On a SLES10 system, I ran the below to setup my first draft of rules. I noticed that the rules come into effect immediately and do not require any restart of iptables.
iptables -A INPUT -j ACCEPT
iptables -A OUTPUT -m... (4 Replies)
Could someone help me with writing rules for iptables?
I need a dos attacks protection for a game server.
port type udp
ports 27015:27030
interface: eth0
Accept all packets from all IPs
Chek if IP sent more than 50 packets per second
Drop all packets from this IP for 5 minutes
I would be... (0 Replies)
Hi Gurus,
I need to add Multicast Port = xyz
Multicast Address = 123.134.143 ( example) to my firewall rules. Can you please guide me with the lines I need to update my iptables files with. (0 Replies)
Hi Champs
i am new in Iptables and trying to write rules for my Samba server.I took some help from internet, created one script and run from rc.local :
#Allow loopback
iptables -I INPUT -i lo -j ACCEPT
# Accept packets from Trusted network
iptables -A INPUT -s my-network/subnet -j... (0 Replies)
Hello,
I have iptables service running on my CentOS5 server. It has approx 50 rules right now.
The problem I am facing now is as follows -
I have to define a new chain in the filter table, say DOS_RULES & add all rules in this chain starting from index number 15 in the filter table.
... (1 Reply)
Hello,
I did 2 scripts. The second one is, I hope, more secure.
What do you think?
Basic connection (no server, no router, no DHCP and the Ipv6 is disabled)
#######script one
####################
iptables -F
iptables -X -t filter
iptables -P INPUT DROP
iptables -P FORWARD... (6 Replies)
Hi, I am relatively new to firewalls and netfilter. I have a Debian Stretch router box running dnsmasq, connected to a VPN. Occasionally dnsmasq polls all of the desired DNS servers to select the fastest. When it does this it responds to replies of the non-selected DNS servers with a icmp type... (0 Replies)
Discussion started by: CrazyDave
0 Replies
LEARN ABOUT DEBIAN
ifscheme
IFSCHEME(8) Commands IFSCHEME(8)NAME
ifscheme - scheme control for network interfaces
SYNOPSIS
ifscheme [-v] [[-s] newscheme]
mapping <interface> script ifscheme-mapping
DESCRIPTION
ifscheme allows you to change network configuraton schemes or query the current scheme. It integrates with the ifup(8) command and inter-
faces(5). For example, you might use this program to configure a "home" scheme and a "work" scheme for a network device on a laptop. When
you move between home and work, a simple command can reconfigure your networking.
If you run the program with no parameters, it will tell what the current network scheme is.
The ifscheme-mapping utility is used to tell the ifup and ifdown utilities about the current scheme.
OPTIONS -v
--verbose
Run in verbose mode. This is passed in to the ifup and ifdown programs as well.
-l
--list list all schemes available/defined in /etc/network/interfaces.
newscheme
-s newscheme
--scheme newscheme
Change to a new network configuration scheme. When the scheme is changed, network interfaces that were using the old scheme will be
taken down and brought back up to use the new configuration scheme. -s or --scheme are mandatory if newscheme begins with a -.
CONFIGURATION
To make the program do anything useful when a scheme is selected, you must edit /etc/network/interfaces to add a mapping for the interface
(or interfaces) that can be controlled on a per-scheme basis. Suppose you want to control eth0 in this way. You might have an existing eth0
configuraton in there, such as:
auto eth0
iface eth0 inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
To change this so you can chose between static routing and dhcp, replace it with the following (it helps to ifdown the interface first).
auto eth0
mapping eth0
script ifscheme-mapping
iface eth0-home inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
iface eth0-work inet dhcp
Now if you run "ifscheme home" and ifup the interface, you'll get the eth0-home configuration stanza. If you run "ifscheme work", it will
be changed to the eth0-work stanza. You can add additional stanzas as desired, but the label must always be of the form <hardware inter-
face>-<scheme name>.
If you have a second interface (perhaps a wireless network card on eth1), you can duplicate the above for that interface, changing the eth0
and the configuration details as appropriate, but remember to add an iface stanza for every scheme name for the second interface.
FILES
/etc/network/interfaces
the interfaces definition file
/etc/network/run/scheme
the current scheme
/etc/network/run/ifstate
a record of the current state of the interfaces, managed by ifup and ifdown
BUGS
All schemed interfaces will have the same scheme.
Any schemed interface which does not have an entry for the current scheme and is not configured when the scheme is changed will not be suc-
cessfully configured when it is brought up.
SEE ALSO interfaces(5)ifup(8)ifdown(8)DISTRIBUTION
Redistribution is subject to the GNU public license.
AUTHORS
Joey Hess <joey@kitenet.net>, Peter Wilson <pwilson@cs.hmc.edu>
IFSCHEME(8)