In my oracle db server we have 15 cores (power8). The output of the vmstat is as below.
Now you can see the run queue and wait queue both are high also entitled capacity is also always 90%. The 15 to 25% cpu is always idle. So is there a cpu bottleneck on this system or its ok, no one complaining but want to know for myself.
Last edited by Don Cragun; 12-29-2016 at 03:46 AM..
Reason: Add CODE tags.
Hello everybody.
I have a problem with my AIX 5.3. Recently my unix shows a high cpu utilization with sar or topas.
I need to find what I have to do to solve this problem, in fact, I don't know what is my problem.
I had the same problem with another AIX 5.3 running the same... (2 Replies)
About 4 years ago I wrote this tool inspired by Rob Urban's collect tool for DEC's Tru64 Unix. What makes this tool as different as collect was in its day is its ability to run at a low overhead and collect tons of stuff. I've expanded the general concept and even include data not available in... (0 Replies)
Hello Friends,
On one of my Solaris 10 box, CPU usage shows 100% using "sar", "vmstat". However, it has 4 CPUs and prstat and glance are not showing enough processes to justify high CPU utilization.
=========================================================================
$ prstat -a
... (4 Replies)
Hi All,
While creating zone we will mention min and max cpu cores, like
add dedicated-cpu
set ncpus=NUM_CPUS_MIN-NUM_CPUS_MAX
end
Ques1:
Suppose thing that non global zone uses only minimum cores at particular time What the other cores will do, Will it shared to global zone?
Ques:2... (1 Reply)
There might be some problem with my server,
because every morning at 7, it's performance become bad with no DB extra deadlock.
But I just couldn't figure it out.
Please give me some advise, thanks a lot...
According to the CPU performace chart, Daily CPU loading Maximum: 42 %, Average:36%.
... (8 Replies)
hi
We have migrated SCO 5.0.6 into ESX4, but the VM eats 100% of the virtual CPU.
Here is top print from the SCO VM:
last pid: 16773; load averages: 1.68, 1.25, 0.98 02:08:41
79 processes: 75 sleeping, 2 running, 1 zombie, 1 onproc
CPU states: 0.0% idle, 17.0% user,... (7 Replies)
We have a DB server which is constantly utilised above 95% above.
This is becoming nuisance when the monitoring team frequently calls to check on it. Frankly I do not know what to tweak or even interpret the outputs.
I noticed constant 30 to 60% in wio column of the cpu utilisation.
There... (1 Reply)
I want to write a shell script which will print AIX
CPU utilization
memory utilization
every 5 mins redirect to file. How do i do it? Please advise.
Which commands I should use? (3 Replies)
Hi all,
Been reading a lot of the cpu load and its "analogy of it to car traffic path of expressway"
From wiki
Most UNIX systems count only processes in the running (on CPU) or runnable (waiting for CPU) states. However, Linux also includes processes in uninterruptible sleep states... (13 Replies)
Discussion started by: javanoob
13 Replies
LEARN ABOUT ULTRIX
vmstat
vmstat(1) General Commands Manual vmstat(1)Name
vmstat - report virtual memory statistics
Syntax
vmstat [ interval [ count ] ]
vmstat -v [ interval [ count ] ]
vmstat -fKSsz
vmstat -Kks namelist [ corefile ]
Description
The command reports statistics on processes, virtual memory, disk, trap, and cpu activity.
If is specified without arguments, this command summarizes the virtual memory activity since the system was last booted. If the interval
argument is specified, then successive lines are summaries of activity over the last interval seconds. Because many statistics are sampled
in the system every five seconds, five is a good specification for interval; other statistics vary every second. If the count argument is
provided, the statistics are repeated count times.
When you run the format fields are as follows:
Procs: information about numbers of processes in various states.
r in run queue
b blocked for resources (i/o, paging, and so on.)
w runnable or short sleeper (< 20 seconds) but swapped
faults: trap/interrupt rate averages per second over the last 5 seconds.
in (non clock) device interrupts per second
sy system calls per second
cs cpu context switch rate (switches/second)
cpu: breakdown of percentage usage of cpu time
us user time for normal and low priority processes
sy system time
id cpu idle time
Memory: information about the use of virtual and real memory. Virtual pages are considered active if they belong to processes which are
running or have run in the last 20 seconds.
avm active virtual pages
fre size of the free list
Pages are reported in units of 1024 bytes.
If the number of pages exceeds 9999, it is shown in a scaled representation. The suffix k indicates multiplication by 1000 and the suffix
m indicates multiplication by 1000000. For example, the value 12345 appears as 12k.
page: information about page faults and paging activity. These are averaged every five seconds, and given in units per second. The size
of a unit is always 1024 bytes and is independent of the actual page size on a machine.
re page reclaims (simulating reference bits)
at pages attached (found in free list not swapdev or filesystem)
pi pages paged in
po pages paged out
fr pages freed per second
de anticipated short term memory shortfall
sr pages scanned by clock algorithm, per-second
disk: s0, s1 ...sn: Paging/swapping disk sector transfers per second (this field is system dependent). Typically paging is split across
several of the available drives. This will print for each paging/swapping device configured into the kernel.
Options-f Provides reports on the number of forks and vforks since system startup and the number of pages of virtual memory involved in each
kind of fork.
-K Displays usage statistics of the kernel memory allocator.
-k Allows a dump to be interrogated to print the contents of the sum structure when specified with a namelist and corefile. This is
the default.
-S Replaces the page reclaim (re) and pages attached (at) fields with processes swapped in (si) and processes swapped out (so).
-s Prints the contents of the sum structure, giving the total number of several kinds of paging related events that have occurred since
boot.
-v Prints an expanded form of the virtual memory statistics.
-z Zeroes out the sum structure if the UID indicates root privilege.
Examples
The following command prints what the system is doing every five seconds:
vmstat 5
To find the status after a core dump use the following:
cd /usr/adm/crash
vmstat -k vmunix.? vmcore.?
Files
Kernel memory
System namelist
vmstat(1)