You might also want to further simplify your program by immediately printing inside the function, without returning anything:
If you know you have only to differentiate between "[[:digit:]]" and "[[:alpha:]]" you can further simplify myprint() to use if ... else instead of separate ifs.
How do I check if a variable consisted of letters, numbers or both letters and numbers?
For example, I have a variable $X and I want to print "1" if it contains only letters, "2" if it contains only numbers and "3" if it contains both (2 Replies)
Hello all I am a unix newbie....
I have a sun netra t1 and it is freaking out
I am connected to it through a console port, and it is just spitting out a ton on numbers and letters like below its just keeps going and going.
I have tried rebooting it and I cannot get it back to any kind of a... (1 Reply)
Hi friends
How can I use "for loop" for decimal numbers?
ex: 0.1 < x < 0.6
I used this commands but does'nt work.
LIMIT=0.6
for ((x=0.1; x<=LIMIT; x++))
do
-
-
-
done
Many thanks (1 Reply)
Hello...
I am new to unix and I am wondering if in a C-shell script , Are we supposed to use only whole numbers........ for example..if a program needs to calculate the average of some numbers........
@ avg = (($1 +$2 + $3)/3)) is returning a whole number.........How can a decimal be... (7 Replies)
If I have a set of strings,
C21
F231
H42
1C10
1F113
and I want to isolate the ints following the char, what would the sed string be to find numbers after letters?
If I do,
*, I will get numbers after letters, but I am looking to do something like,
sed 's/*/\t*/g'
this will give me... (14 Replies)
Hi,
I columns with both number and letters however i need the number 4 trimmed off the lines that have 3 numbers in them so it just because the 2 preceding numbers only
For example
V25QG2-K18QG-V25CG2
L26HG-L17HA-L26CG
I434QD1-L19HB2-I434CD1
I434QD1-A31QB-I434CD1 ... (7 Replies)
Hi Experts,
I am finding difficulty to get exact match:
file
OPERATING_SYSTEM=HP-UX
LOOPBACK_ADDRESS=127.0.0.1
INTERFACE_NAME="lan3"
IP_ADDRESS="10.53.52.241"
SUBNET_MASK="255.255.255.192"
BROADCAST_ADDRESS=""
INTERFACE_STATE=""
DHCP_ENABLE=0
INTERFACE_NAME="lan3:1"... (6 Replies)
Hello,
I have a file such as this:
chr1
chr2
chr1
chr2
chr3
chr10
chr4
chr5
chrz
chr1AI want to sort it, I use this command:
sort -k1 -th -n testfilebut I get this output, how can I fix this?
chr1
chr1
chr10
chr1A
chr2
chr2 (3 Replies)
I have a file with hundreds of lines in it. I wanted to extract anything that matches the following:
KR followed by 4 digits:
example KR1201
cat list | sed "s///g"
Is the closest I've come, and obviously it is not what I want. This would remove all of the items that I want and leave me... (2 Replies)
Heyas
Just a little fun script (code block) i'd like to share for fun.
#/bin/bash
# roman.sh
#
# Function
#
num2roman() { # NUM
# Returns NUM in roman letters
#
input=$1 # input num
output="" # Clear output string
len=${#input} # Initial length to count down
... (9 Replies)
Discussion started by: sea
9 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)