12-20-2016
You need MOS access and a valid service contract with Oracle. Then you can download the CAM software which comes with all the FW for all supported storages.
10 More Discussions You Might Find Interesting
1. Solaris
We're moving our production 3510FC to development, so we need to replace the production 3510FC. The 6140 is nice, but pricey.
Here's the question: Would two 2540's (RAID 10) be 'faster' than one 3510? (RAID 10) and faster than one 6140 (RAID 10)?
One StoregeTek 6140 (16x72GB 15k rpm fc-al... (12 Replies)
Discussion started by: buddhavelvet
12 Replies
2. Solaris
I can't seem to get my host to see a 2540 array.
I have 3 arrays right now. (2) 2540's.. let's call them 2540A and 2540B and (1) 6140. 2540A and the 6140 are configured and mounted on the same linux host.
For the life of me, I cannot get the other problem-child 2540B to be recognized by the... (6 Replies)
Discussion started by: buddhavelvet
6 Replies
3. Solaris
Hi,
I have a simple question on how to correctly disable the matrix?
Looking for the Common Array Manager and I do not see this option...
Thank for help (3 Replies)
Discussion started by: bieszczaders
3 Replies
4. Solaris
Hi peeps,
Was wondering if anyone can help me, got a couple of storagetek 2540's that I need to configure. Trouble is I think they were brought as second user as all that came with them was cables.
Does anyone know how to configure them (i.e. create raid sets and map to Luns and present... (1 Reply)
Discussion started by: callmebob
1 Replies
5. Hardware
Hello all !
I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server.
I... (2 Replies)
Discussion started by: acorradi
2 Replies
6. Hardware
Hi all,
My Sun StorageTek 2540 have redundant batteries, but a battery was failed.
# /opt/SUNWstkcam/bin/sscs list -d MyStorage1 fru
Name FRU Alarm State Status Revision Unique Id
-------------------------- ----------- --------... (2 Replies)
Discussion started by: buyantugs
2 Replies
7. Hardware
Hi Guys and Gals,
Wionder if you could help me, got a problem with a controller on a storagetek 2540, dead when fully powered up but if you reboot, it is ok for a couple of seconds (and you can ping it). Then once the array is fully up, it goes faulty and is un-pingable.
Had anyone... (4 Replies)
Discussion started by: callmebob
4 Replies
8. Hardware
Hi Guys and Gals,
does anyone know how to update the firmware on the drives in a storagetek 2540?
Thanks in advance
Rgrds
Martin (0 Replies)
Discussion started by: callmebob
0 Replies
9. Solaris
Bought a Sun StorageTek 2540 SAN array a few years ago from a company that was going out of business. When we first set it up, we were able to get all the software (Common Array Manager) and firmware directly from Sun.
We just upgraded the drives, but the array is too large for the firmware. Now... (6 Replies)
Discussion started by: edison303
6 Replies
10. Solaris
Hello Dears,
My server hots cannot contacted my array disk 2540 by using out-of-band Ethernet Cable.
The Controller Ethernet port is off , I replace the ethernet cable but not OK
I reboot the server and the Array disk 2540 but Not OK.
Please somebody know how to solve this issue?
... (1 Reply)
Discussion started by: ghislino
1 Replies
XPT(4) BSD Kernel Interfaces Manual XPT(4)
NAME
xpt -- CAM transport layer interface
SYNOPSIS
None.
DESCRIPTION
The xpt driver provides a way for userland applications to issue certain CAM CCBs to the kernel.
Since the xpt driver allows direct access to the CAM subsystem, system administrators should exercise caution when granting access to this
driver. If used improperly, this driver can allow userland applications to crash a machine or cause data loss.
KERNEL CONFIGURATION
There is no kernel configuration required for the xpt driver. It is enabled when SCSI support is enabled in the kernel. There is one
instance of the xpt driver per CAM transport layer instance. Since there is currently only one CAM transport layer, there will only be one
instance of this driver.
IOCTLS
CAMIOCOMMAND This ioctl takes certain kinds of CAM CCBs and passes them through to the CAM transport layer for action. Only the following
CCB types are supported:
XPT_SCAN_BUS
XPT_RESET_BUS
XPT_SCAN_LUN
XPT_ENG_INQ
XPT_ENG_EXEC
XPT_DEBUG
XPT_DEV_MATCH
XPT_PATH_INQ
The above CCBs are the only ones supported since it makes more sense to send them through a generic passthrough device rather
than a passthrough device tied to a particular underlying SCSI device.
CAMGETPASSTHRU This ioctl takes an XPT_GDEVLIST CCB, and returns the passthrough device corresponding to the device in question.
FILES
/dev/xpt0 Character device node for the xpt driver.
DIAGNOSTICS
None.
SEE ALSO
cam(3), cam_cdbparse(3), pass(4), camcontrol(8)
HISTORY
The CAM transport layer driver first appeared in FreeBSD 3.0.
AUTHORS
Kenneth Merry <ken@FreeBSD.org>
BSD
October 10, 1998 BSD