Seems like Solaris-11 is not compatible/supported for this software. I have installed as per your downloadable link, but it is generating dump. If this is so, I need not go back and remove both SAS cables and plug them on MB "somewhere" and that will bypass RAID controller.
We used kstat on netra240/440 to check if the link is full duplex. So we do something like:
bash-3.00# kstat -pc net bge:1::/'link_duplex'/ | cut -f2
2
The output 2 indicates the link is full duplex. This kind of check worked all right for Netra 240/440 systems.
However, the nxge... (2 Replies)
I 've 2 different T5220 and both are showing different prompts when i ssh to the console.
1. Shows sc> ALOM
2. Shows -> ILOM
as far as i know the T5220 comes with ILOM , so why i 'm seeing 2 different type of console for same tyep of hardware ?
and i found that we... (6 Replies)
Hi,
SC on one of my T5220 is not responding .. it does not show not let me type anything .. what could be the reason for it ? though when i powercycle the box from sc it shows me the system coming up but after that does not let me login thru sc
sc> console -f
Enter #. to return to ALOM. (2 Replies)
We're just about to migrate a large application from an Enterprise 6900 to a pair of T5220s utilising LDOMs. Does anyone have any experience of LDOMs on this kit and can provide any recommendations or pitfalls to avoid?
I've heard that use of LDOMs can have an impact on I/O speeds as it's all... (9 Replies)
Hi,
We have two T5220 servers in our datacentre
one server is showing 64 processors online
and another showing 32 processors online
two are newly purchased, there is no hardware faults in this server
one server has 64gb memory and it shows 64 processors,
and other having 32gb memory and it... (5 Replies)
I have a new T5220 racked at our remote office and the guys who racked it does not know how to configure the SP on the system .. is there any way i can do it remotely ? (1 Reply)
I'm trying to use a V210 (sun4u) configured as a jumpstart server to flash install a number of T5220's (sunv4).
The Facts:
V210 - Solaris 10 (September 2010 Release / not patched)
T5220's - Archive's created using prior (unknown) version of solaris 10.
Flar -i <archive name> shows the... (6 Replies)
Hi Guys and Gals,
Wondering if anyone could help me, tricky one this.
Got a T5220 with a graphics card. When you power it on, it outputs its output to the screen and you can type commands with the keyboard etc.
But no matter what version of Solaris 10 you use, when you do a boot cdrom... (1 Reply)
Hello guys,
can anyone give me some advice on how to perform
clean installation of Solaris 10 on T5220 ?
I am connected with serial management port on the machine,
i have the ok promt and now i should eject the dvdrom to insert
Solaris dvd into and start the clean install.
So how to do that... (3 Replies)
We have one box T5220 which was assigned 2x100G Luns but i have a strange problem if i use powermt display it only shows me one card but cfgadm, fcinfo commands shows 2 dual port cards as up. What could be the reason for it. I already did a re-configure reboot but that didn't help. Can anyone help... (1 Reply)
Discussion started by: fugitive
1 Replies
LEARN ABOUT DEBIAN
usb
USB(4) BSD Kernel Interfaces Manual USB(4)NAME
usb -- Universal Serial Bus
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device usb
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
usb_load="YES"
USERLAND PROGRAMMING
USB functions can be accessed from userland through the libusb library. See libusb(3) for more information.
DESCRIPTION
FreeBSD provides machine-independent bus support and drivers for USB devices in host and device side mode.
The usb driver has three layers:
USB Controller (Bus)
USB Device
USB Driver
The controller attaches to a physical bus like pci(4). The USB bus attaches to the controller, and the root hub attaches to the controller.
Any devices attached to the bus will attach to the root hub or another hub attached to the USB bus.
The uhub device will always be present as it is needed for the root hub.
INTRODUCTION TO USB
The USB is a system where external devices can be connected to a PC. The most common USB speeds are:
Low Speed (1.5MBit/sec)
Full Speed (12MBit/sec)
High Speed (480MBit/sec)
Each USB has a USB controller that is the master of the bus. The physical communication is simplex which means the host controller only com-
municates with one USB device at a time.
There can be up to 127 devices connected to an USB HUB tree. The addresses are assigned dynamically by the host when each device is attached
to the bus.
Within each device there can be up to 16 endpoints. Each endpoint is individually addressed and the addresses are static. Each of these
endpoints will communicate in one of four different modes: control, isochronous, bulk, or interrupt. A device always has at least one end-
point. This endpoint has address 0 and is a control endpoint and is used to give commands to and extract basic data, such as descriptors,
from the device. Each endpoint, except the control endpoint, is unidirectional.
The endpoints in a device are grouped into interfaces. An interface is a logical unit within a device; e.g. a compound device with both a
keyboard and a trackball would present one interface for each. An interface can sometimes be set into different modes, called alternate set-
tings, which affects how it operates. Different alternate settings can have different endpoints within it.
A device may operate in different configurations. Depending on the configuration, the device may present different sets of endpoints and
interfaces.
The bus enumeration of the USB bus proceeds in several steps:
1. Any interface specific driver can attach to the device.
2. If none is found, generic interface class drivers can attach.
SEE ALSO
The USB specifications can be found at:
http://www.usb.org/developers/docs/
libusb(3), usbdi(4), aue(4), axe(4), cue(4), ehci(4), kue(4), ohci(4), pci(4), rue(4), ucom(4), udav(4), uhci(4), uhid(4), ukbd(4), ulpt(4),
umass(4), ums(4), uplcom(4), urio(4), uvscom(4), usbconfig(8)STANDARDS
The usb module complies with the USB 2.0 standard.
HISTORY
The usb module has been inspired by the NetBSD USB stack initially written by Lennart Augustsson. The usb module was written by Hans Petter
Selasky <hselasky@freebsd.org>.
BSD May 20, 2009 BSD