Let me go to DC and open server, will try to figure it
-------------------------------------------------------------------
Removing card and messing with connections and MB was not agreed with management and they said to go with RAID 1 for rpool and RAID 5 for application/db filesystems.
Do we have any tools/utility, which can be managed from OS level and we can check status/configuration from there ?
All I can see is below, but it is not giving much details :-
Last edited by DukeNuke2; 12-17-2016 at 11:35 AM..
We used kstat on netra240/440 to check if the link is full duplex. So we do something like:
bash-3.00# kstat -pc net bge:1::/'link_duplex'/ | cut -f2
2
The output 2 indicates the link is full duplex. This kind of check worked all right for Netra 240/440 systems.
However, the nxge... (2 Replies)
I 've 2 different T5220 and both are showing different prompts when i ssh to the console.
1. Shows sc> ALOM
2. Shows -> ILOM
as far as i know the T5220 comes with ILOM , so why i 'm seeing 2 different type of console for same tyep of hardware ?
and i found that we... (6 Replies)
Hi,
SC on one of my T5220 is not responding .. it does not show not let me type anything .. what could be the reason for it ? though when i powercycle the box from sc it shows me the system coming up but after that does not let me login thru sc
sc> console -f
Enter #. to return to ALOM. (2 Replies)
We're just about to migrate a large application from an Enterprise 6900 to a pair of T5220s utilising LDOMs. Does anyone have any experience of LDOMs on this kit and can provide any recommendations or pitfalls to avoid?
I've heard that use of LDOMs can have an impact on I/O speeds as it's all... (9 Replies)
Hi,
We have two T5220 servers in our datacentre
one server is showing 64 processors online
and another showing 32 processors online
two are newly purchased, there is no hardware faults in this server
one server has 64gb memory and it shows 64 processors,
and other having 32gb memory and it... (5 Replies)
I have a new T5220 racked at our remote office and the guys who racked it does not know how to configure the SP on the system .. is there any way i can do it remotely ? (1 Reply)
I'm trying to use a V210 (sun4u) configured as a jumpstart server to flash install a number of T5220's (sunv4).
The Facts:
V210 - Solaris 10 (September 2010 Release / not patched)
T5220's - Archive's created using prior (unknown) version of solaris 10.
Flar -i <archive name> shows the... (6 Replies)
Hi Guys and Gals,
Wondering if anyone could help me, tricky one this.
Got a T5220 with a graphics card. When you power it on, it outputs its output to the screen and you can type commands with the keyboard etc.
But no matter what version of Solaris 10 you use, when you do a boot cdrom... (1 Reply)
Hello guys,
can anyone give me some advice on how to perform
clean installation of Solaris 10 on T5220 ?
I am connected with serial management port on the machine,
i have the ok promt and now i should eject the dvdrom to insert
Solaris dvd into and start the clean install.
So how to do that... (3 Replies)
We have one box T5220 which was assigned 2x100G Luns but i have a strange problem if i use powermt display it only shows me one card but cfgadm, fcinfo commands shows 2 dual port cards as up. What could be the reason for it. I already did a re-configure reboot but that didn't help. Can anyone help... (1 Reply)
Discussion started by: fugitive
1 Replies
LEARN ABOUT DEBIAN
dpt
DPT(4) BSD Kernel Interfaces Manual DPT(4)NAME
dpt -- DPT RAID Controller SCSI driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device dpt
For one or more EISA cards:
device eisa
For one or more ISA cards:
device isa
For one or more PCI cards:
device pci
To allow PCI adapters to use memory mapped I/O if enabled:
options DPT_ALLOW_MEMIO
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
dpt_load="YES"
DESCRIPTION
The dpt driver supports DPT RAID SCSI controllers.
SmartRAID (PM3???) are "Enterprise" class cards, and SmartCache (PM2???) cards are in the "Workstation" class. The Gen 4 Smart Cache IV
products were a re-issue of the Gen 3 utilizing upgraded (and cheaper to produce) silicon. The PM3334 (Smart RAID III) was not revamped as
there was no upgraded silicon (68040 processor) and it was using the best DPT made. Note there has been customer confusion over the faster
enterprise class card supported by this driver being an older generation. The Gen5 cards are supported by the asr(4) driver.
HARDWARE
The dpt driver provides support for the following RAID adapters:
o DPT Smart Cache Plus
o Smart Cache II (PM2?2?, PM2022 [EISA], PM2024/PM2124 [PCI]) (Gen2)
o Smart RAID II (PM3?2?, PM3021, PM3222)
o Smart Cache III (PM2?3?)
o Smart RAID III (PM3?3?, PM3332 [EISA], PM3334UW [PCI]) (Gen3)
o Smart Cache IV (PM2?4?, PM2042 [EISA], PM2044/PM2144 [PCI]) (Gen4)
o Smart RAID IV
SEE ALSO asr(4), cd(4), ch(4), da(4), sa(4), scsi(4)HISTORY
The dpt driver first appeared in FreeBSD 2.2.6.
AUTHORS
The dpt driver was written by Simon Shapiro and ported to the CAM SCSI system by Justin T. Gibbs.
BSD June 18, 2006 BSD