12-16-2016
How do I configure SAS drive on the PC first to detect on HP server ML350 G5
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi friends,
i am getting the following error while booting my system which has SCo UNIX .
=========================
H iinit
PANIC: srmountfun-Error 22
mounting of rootdev hd(1/42)
cannot dump 40863 pages to dempdev hd(1/41) : Space for only 0 pages.
Dump not completed.
safe to power off... (3 Replies)
Discussion started by: sveera
3 Replies
2. SCO
hi, i m a newbie and installed sco unix on my machine. Also i installed win-xp. i tried to modify the boot.ini file but it does not give me a choice in the begining.
please guide me on this. do we get a boot loader for unix like LILO or GRUB?
:confused: (3 Replies)
Discussion started by: 187final
3 Replies
3. SCO
anyone know where I can download or get a boot disk for sco unix v/386? I have an old PC running sco unix v/386 3.2. I dont have an install or boot disk. I need to reset the root password. I have looked all over the internet and cannot find it anywhere. any help would be greatly appreciated.... (5 Replies)
Discussion started by: format
5 Replies
4. SCO
Hi i have a problem after boot with N1 disk and putting N2 disk and pressing the enter in this message:Insert N2(filesystem) floppy and press after by this(pressing enter) the system is reboot!! why??? :confused:
my old pc is a Pentium II 333mhz 3gb hd 64mb ram
please help!! :( (3 Replies)
Discussion started by: panos_pit
3 Replies
5. SCO
Our system is not booting up properly. It keeps going to this screen:
Enter Run Level (0-6, s or S):
I tried to hit all nos# 0-6 is just goes to hung state.
Tried s or S & it brings me to single user mode. I've checked the file systems & found out that all three had 98%. I tried to... (86 Replies)
Discussion started by: jedimaster
86 Replies
6. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
7. UNIX for Dummies Questions & Answers
UNIX sco release 5.05 system does not boot:cannot open device hd(40)/boot
stage 1 boot failure: error loading hd(40)/bootWhat to do? (2 Replies)
Discussion started by: Joaoalpande
2 Replies
8. SCO
UNIX sco release 5.05 system does not boot:
cannot open device hd(40)/boot
stage 1 boot failure: error loading hd(40)/boot
what to do? (1 Reply)
Discussion started by: Joaoalpande
1 Replies
9. UNIX for Advanced & Expert Users
UNIX sco release 5.05 system does not boot:
cannot open device hd(40)/boot
stage 1 boot failure: error loading hd(40)/boot
what to do? (5 Replies)
Discussion started by: Joaoalpande
5 Replies
10. SCO
HI All,
I have an old SCO-UNIX machine which I support a long standing client / friend with.
I don't use it very often, and is kept switched off. All was well 2 weeks ago, but when I tried to boot today all I get is a continuous set of long beeps but no booting. I have checked inside... (4 Replies)
Discussion started by: andy sleight
4 Replies
LEARN ABOUT SUSE
smp_rep_phy_err_log
SMP_REP_PHY_ERR_LOG(8) SMP_UTILS SMP_REP_PHY_ERR_LOG(8)
NAME
smp_rep_phy_err_log - invoke REPORT PHY ERROR LOG SMP function
SYNOPSIS
smp_rep_phy_err_log [--help] [--hex] [--interface=PARAMS] [--phy=ID] [--raw] [--sa=SAS_ADDR] [--verbose] [--version] SMP_DEVICE[,N]
DESCRIPTION
Sends a SAS Management Protocol (SMP) REPORT PHY ERROR LOG request function to a SMP target. The SMP target is identified by the SMP_DEVICE
and the SAS_ADDR. Depending on the interface, the SAS_ADDR may be deduced from the SMP_DEVICE. With one interface there is one SMP_DEVICE
per machine so the SMP_DEVICE,N syntax is needed to differentiate between HBAs if there are multiple present.
OPTIONS
Mandatory arguments to long options are mandatory for short options as well.
-h, --help
output the usage message then exit.
-H, --hex
output the response in hexadecimal.
-I, --interface=PARAMS
interface specific parameters. In this case "interface" refers to the path through the operating system to the SMP initiator. See
the smp_utils man page for more information.
-p, --phy=ID
phy identifier. ID is a value between 0 and 127. Default is 0.
-r, --raw
send the response to stdout in binary. All error messages are sent to stderr.
-s, --sa=SAS_ADDR
specifies the SAS address of the SMP target device. Typically this is an expander. This option may not be needed if the SMP_DEVICE
has the target's SAS address within it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number
in hexadecimal either prefix it with '0x' or put a trailing 'h' on it.
-v, --verbose
increase the verbosity of the output. Can be used multiple times
-V, --version
print the version string and then exit.
NOTES
Similar information is maintained for SAS SSP target phys (e.g. on a SAS disk). It can be obtained from the Protocol Specific Port log page
with the sg_logs utility.
Similar information may be obtained for SAS initiator phys (e.g. on a SAS HBA). As an example in Linux 2.6.28 error information can be
found in this directory /sys/class/sas_phy/phy-4:0 (for the phy 0 in SCSI/SAS host 4).
Similar information may be obtained for SATA device phys (e.g. on a SATA disk). If there is a SAT layer between OS and the SATA device then
the sg_sat_phy_event utility can fetch the information.
CONFORMING TO
The SMP REPORT PHY ERROR LOG function was introduced in SAS-1 . The "Expander change count" field was added in SAS-2 .
AUTHORS
Written by Douglas Gilbert.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright (C) 2006-2008 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE.
SEE ALSO
smp_utils, smp_phy_control(smp_utils), sg_logs(sg3_utils), sg_sat_phy_event(sg3_utils)
smp_utils-0.94 December 2008 SMP_REP_PHY_ERR_LOG(8)