I made a named pipe and seems very close to getting my solution of garbing HTTP headers, Also noticed my browser does not Always send all the header each time.
(Chrome Version 54.0.2840.99 even in incognito )
My workaround (not solution) have a named pipe to communicated with nc.
and then have the while loop to feed netcat(nc)
I am just playing around with named pipe, looking to find something in the lines of:
and then loop out with tail kind of thing on webin and webout. Any experts on FIFO's please suggest.
Last edited by chakrapani; 12-15-2016 at 11:50 AM..
Reason: typo
Hi Folks
I am not a c programmer .But i need help in writing a program which can do this any ideas on how to go about it .
i start a server on the target server where files need to be copied
start-server -port 5006 & ---start the server and listen it on a partcular port
on the source... (2 Replies)
I'd like to do a data transfer without encryption but with a guarantee that my data comes from a legit source. I'm thinking something that uses a public key scheme to sign the data.
Does anyone know of something like that?
Thanks!
-Pileofrogs (1 Reply)
Is there a way how to react on the message a client sent to the server?
I would like as the client sent message to server: "get information such and such" and server would answer.
Thank you for reply! (6 Replies)
Hi all,
When using netcat to transfer the data over socket, if no connection is established, how long will netcat keep the data; will it discard the "oldest" data ?
Say for example I use "Some Command | netcat -l -p port", the command I use will generate a lot of output constantly, while no... (2 Replies)
Please direct me to the right forum tree if i am in the wrong section for this.
i have netcat on a unix machine and there is no man nc or man netcat available.
my command i am using is:
cat $FILE1 | netcat -h $PRINTER -p 9100
(-h -p -d are the only flags available in this version of... (3 Replies)
hello guys, i want to install netcat on my solaris. after i tar and gunzip netcat i'm confuse what do i must to do ? please help me to install netcat on my solaris. I'm beginner :( (2 Replies)
Hello,
Thank you very much for the line nc -lp <port> . I tried to run simple chat session with nc as it's shown in catonmatDOTorg but failed miserably with that syntax inspite of opening port 7777 by iptables . But your command example is working nicely.
So a bagful of thanks :))
Only one... (0 Replies)
Hi;
I have a url like
http://localhost:8080/examples/jsp/dates/nextPageToPost.jsp?name=ajay&password=pas&sex=Male&check=on&nationality=USA&description=aa&submit=submit
in which i want to use nc for http post for parameters like "name","password"....etc
can neone please help me how to do that... (3 Replies)
Hi all,
I know my question is regarding Windows and not Linux, but I simply need people who know Netcat pretty well and I'm guessing here is a good place for that. So on with my question.
I'm doing some research, and I was playing around with netcat on a WinXP VM but I can't seem to get... (0 Replies)
Currently I run a number of network tests using netcat that checks for an open port on a remote IP-address, using this syntax:
netcat -v -w 5 -z 107.249.95.5 4488
For some reason, the netcat command above is hanging (although others work fine), but a telnet is showing a valid connection like... (4 Replies)
Discussion started by: ckmehta
4 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)